Auto Parts Search
Ford Probe CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Year
| 1997 | 1996 | 1995 | 1994 |
| 1993 | 1992 | 1991 | 1990 |
| 1989 |
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about Ford Probe car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Probe automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR Ford Probe AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported Ford Probe cars and light trucks from 1990+
Vacuum & Wiring Diagrams -> Passenger Cars -> Electric Cooling Fans
Vehicle: 1993 Ford Probe GT 2.5 V6 GAS
CLICK HERE TO GET FULL ACCESS TO Ford Probe A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR Ford Probe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported Ford Probe cars and light trucks from 1990+.
Anti-Lock Brakes -> Probe -> System Service -> ABS Control Module -> ABS Relay -> Brake System Bleed -> Component Replacement -> Front Speed Sensor -> Front Wheel Sensor Rotor -> Hydraulic Actuation Unit -> Rear Speed Sensor -> System Priming
Vehicle: 1997 Ford Probe 2.0 L4 GAS
Brake System Bleed
Pressure bleeding is recommended for all hydraulic brake systems.
The bleeding operation itself is fairly well standardized. The first step in all cases is cleaning the dirt from the filler cap before removing it from the master cylinder. This should be done thoroughly.
Pressure bleeding is fastest because the master cylinder doesn't have to be refilled several times, and the job can be done by one person. To prevent air from the pressure tank getting into the lines, do not shake the tank while air is being added to the tank or after it has been pressurized. Set t...
CLICK HERE TO GET FULL ACCESS TO Ford Probe BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR Ford Probe AUTOMOBILES
Fuel filter replacement procedures with corresponding images for most domestic and imported Ford Probe cars and light trucks sold in the U.S. for 1980+.
Ford Motor Co. Passenger Cars -> Fuel Pressure Relief -> 1989-97 Probe
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
When installing the fuel filter, ensure the flow arrow is facing in the proper direction.
After the battery has been disconnected and reconnected, some abnormal driveabil...
CLICK HERE TO GET FULL ACCESS TO Ford Probe FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR Ford Probe AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported Ford Probe cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1993 Ford Probe SE 2.0 L4 GAS
When removing both Lefthand front wheel driveshaft and joint and Righthand front wheel driveshaft and joint, Transaxle Plugs T88C-7025-AH must be installed. Failure to use this tool can result in dislocation of differential side gears on 4EAT and MTX equipped vehicles. Should differential side gears become misaligned, differential will have to be removed from transaxle to re-align differential side gears.
- Raise and support vehicle.
- Remove lug nut and wheel and tire assembly.
- Carefully raise staked portion of front axle wheel hub retainer by using a small cape chisel and a ha...
CLICK HERE TO GET FULL ACCESS TO Ford Probe DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR Ford Probe AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported Ford Probe cars and light trucks from 1990+.
Starter, Replace -> Automatic Transaxle -> Manual Transaxle
Vehicle: 1997 Ford Probe GT 2.5 V6 GAS
Manual Transaxle
When servicing starter or performing any maintenance in the area of starter, note heavy gauge input lead connected to starter solenoid is Hot at all times.
- Disconnect battery ground cable, then isolate cable end with electrical tape or equivalent.
- Remove fresh air duct and the air cleaner assembly.
- Disconnect wiring electrical connections from starter motor assembly.
- Remove starter motor retaining bolts, then starter motor from vehicle.
- Reverse procedure to install, noting the following:
- Torque starter motor retaining bolts to 33 ft. lbs.
- Torque starter solenoid B-term...
CLICK HERE TO GET FULL ACCESS TO Ford Probe STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Powertrain Malfunction Indicator ->
Vehicle: 1992 Ford Probe GL 2.2 L4 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected in the powertrain system. If the lamp remains On a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Powertrain Malfunction Indicator will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
CLICK HERE TO GET FULL ACCESS TO Ford Probe MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR Ford Probe AUTOMOBILES
Includes radiator, cooling and heater hose replacement procedures for domestic and imported Ford Probe cars and light trucks from 1990+
Radiator, Replace
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
Allow radiator to cool prior to beginning following procedure. Slowly remove radiator cap to release system pressure. Caution must be used as system contains scalding hot fluid which when under pressure can blow out of radiator fill neck, causing personal injury.
- Slowly remove radiator cap, then open drain valve at bottom of radiator and drain system.
- Remove fresh air duct.
- Remove upper and lower radiator hoses.
- Disconnect overflow hose.
- Disconnect...
CLICK HERE TO GET FULL ACCESS TO Ford Probe RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR Ford Probe AUTOMOBILES
Serpentine belt replacement procedures with corresponding images for most domestic and imported Ford Probe cars and light trucks sold in the U.S. from 1990+.
Serpentine Drive Belt, Replace
Vehicle: 1991 Ford Probe LX 3.0 V6 GAS
If the serpentine belt is to be reused, mark rotation direction on belt for installation reference. Failure to do so may result in belt noise.
- Remove plastic belt shield from power steering pump.
- Insert a 1/2 inch drive br...
CLICK HERE TO GET FULL ACCESS TO Ford Probe SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR Ford Probe AUTOMOBILES
Component location diagrams for most Ford Probe cars and light trucks sold in the U.S. from 1990+.
 Fuel Injection Components Diagram for 1996 Ford Probe GT 2.5 V6 GASComponents on diagram: |
 RH Front Of Engine Compartment Diagram for 1989 Ford Probe GL 2.2 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Ford Probe PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR Ford Probe AUTOMOBILES
OEM drawn wiring diagrams for most Ford Probe cars and light trucks sold in the U.S.
 1991 Ford Probe GL 2.2 L4 GAS Wiring DiagramComponents on diagram: |
 1995 Ford Probe SE 2.0 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Ford Probe WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR Ford Probe AUTOMOBILES
OEM TSB listings for most Ford Probe cars and light trucks sold in the U.S. from 1985+.
|
Document: A/C - IDENT OF NON-APPROVED REFRIGERANTS - REV Vehicle: 1995 Ford Probe SE 2.0 L4 GAS Auto Systems: |
|
Document: BATTERY - STATE OF CHARGE INSTRUCTIONS - S/M REV/ADD Vehicle: 1992 Ford Probe LX 3.0 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO Ford Probe TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR Ford Probe AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most Ford Probe cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO Ford Probe SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your Ford Probe vehicle.
|
| Access the Complete guide! |
