Auto Parts Search
1996 Ford Probe CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1996 Ford Probe car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Probe automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Electrical Symbol & Wire Color Code Identification -> Wire Color Code Identification -> Domestic Vehicles
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Disc Brakes -> Rear Disc Brakes & Parking Brakes -> Caliper Service -> Assemble -> Caliper Overhaul -> Caliper, Replace -> Capri -> Cleaning & Inspection -> Continental, Cougar, Mark VIII, Mustang, Sable, Taurus & Thunderbird -> Contour & Mystique -> Crown Victoria, Grand Marquis & Town Car -> Disassemble -> Escort, Probe & Tracer -> Inspection -> Installation -> Removal
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
Caliper, Replace
Capri
- Raise and support vehicle, then remove wheel and tire assembly.
- Remove brake pads as described under "Brake Pad Service."
- Remove clip brake flex hose to strut assembly clip.
- Remove brake flex hose to caliper assembly banjo bolt.
- Remove two copper washers sealing flex hose banjo fitting, then discard washers.
- Remove lower caliper retaining bolt.
- Using cold chisel, remove upper caliper guide pin dust cap. This will allow access to Allen head on guide pin.
- Using Allen wrench, loosen and remove upper caliper guide pin.
- Lift caliper off rotor.
- Remove guide pin and bushing d...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Ford Motor Co. Passenger Cars -> Fuel Pressure Relief -> 1989-97 Probe
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
When installing the fuel filter, ensure the flow arrow is facing in the proper direction.
After the battery has been disconnected and reconnected, some abnormal driveabil...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
- Raise and support vehicle.
- Remove lug nut and wheel and tire assembly.
- Carefully raise staked portion of front axle wheel hub retainer by using a small cape chisel and a hammer.
- When loosening front axle wheel hub retainer, lock wheel hub by applying brakes. Remove and discard front axle wheel hub retainer. Front axle wheel hub retainer must never be reused.
- Remove stabilizer bar link from front suspension lower arm to ease separation of ball joint from ball joint clamp.
- Remove ball joint clamp bolt.
- Pry ball joint from front wheel knuckle.
- Separate front wheel driveshaft and jo...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Starter, Replace -> Automatic Transaxle -> Manual Transaxle
Vehicle: 1996 Ford Probe GT 2.5 V6 GAS
Manual Transaxle
When servicing starter or performing any maintenance in the area of starter, note heavy gauge input lead connected to starter solenoid is Hot at all times.
- Disconnect battery ground cable, then isolate cable end with electrical tape or equivalent.
- Remove fresh air duct and the air cleaner assembly.
- Disconnect wiring electrical connections from starter motor assembly.
- Remove starter motor retaining bolts, then starter motor from vehicle.
- Reverse procedure to install, noting the following:
- Torque starter motor retaining bolts to 33 ft. lbs.
- Torque starter solenoid B-term...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Ford Motor Co. Cars -> Air Bag Warning Lamp ->
Vehicle: 1996 Ford Probe GT 2.5 V6 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned On as a bulb check. If the Air B...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Radiator, Replace
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
Allow radiator to cool prior to beginning following procedure. Slowly remove radiator cap to release system pressure. Caution must be used as system contains scalding hot fluid which when under pressure can blow out of radiator fill neck, causing personal injury.
- Slowly remove radiator cap, then open drain valve at bottom of radiator and drain system.
- Remove fresh air duct.
- Remove upper and lower radiator hoses.
- Disconnect overflow hose.
- Disconnect...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1996 Ford Probe AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1996 Ford Probe SE 2.0 L4 GAS
- Loosen tensioner locknut.
- Loosen tensioner adjusti...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1996 Ford Probe AUTOMOBILES
Component location diagrams for most 1996 Ford Probe cars and light trucks sold in the U.S. from 1990+.
 Body Lamp Components Diagram for 1996 Ford Probe GT 2.5 V6 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1996 Ford Probe AUTOMOBILES
OEM drawn wiring diagrams for most 1996 Ford Probe cars and light trucks sold in the U.S.
 1996 Ford Probe SE 2.0 L4 GAS Wiring DiagramComponents on diagram: |
 1996 Ford Probe SE 2.0 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1996 Ford Probe AUTOMOBILES
OEM TSB listings for most 1996 Ford Probe cars and light trucks sold in the U.S. from 1985+.
|
Document: RECALL - CERTAIN 1992-2003 MODEL YEAR CARS AND TRUCKS - FUSED JUMPER HARNESS REPLACEMENT FOR VEHICLES SERVICED WITH AN INCOMPATIBLE FUSED JUMPER HARNESS Vehicle: 1996 Ford Probe GT 2.5 V6 GAS Auto Systems: |
|
Document: RECALL - 1992-2004 MULTIPLE VEHICLE LINES - SPEED CONTROL SYSTEM MODIFICATION Vehicle: 1996 Ford Probe GT 2.5 V6 GAS |
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1996 Ford Probe AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1996 Ford Probe cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1996 Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1996 Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1996 Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Probe SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
