Auto Parts Search
1995 Ford Probe CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1995 Ford Probe car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Probe automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR 1995 Ford Probe AUTOMOBILES
Component Replacement & Adjustment -> Passenger Cars -> A/C CLUTCH CYCLE SWITCH, REPLACE
Vehicle: 1995 Ford Probe GT 2.5 V6 GAS
- On Contour and Mystique models, remove battery, power distribution box and battery tray to gain access to A/C cycling switch.
- On all models, disconnect wire harness connector from the ...
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1995 Ford Probe AUTOMOBILES
Drum Brakes -> Type 1 -> Precautions
Vehicle: 1995 Ford Probe GT 2.5 V6 GAS
When working on or around brake assemblies, care must be taken to prevent breathing asbestos dust. Many manufacturers incorporate asbestos fibers in the production of brake linings. During routine service operations the amount of asbestos dust from brake lining wear is at a low level, due to a chemical breakdown during use. Do not sand or grind brake linings unless suitable local exhaust ventilation equipment is used to prevent excessive asbestos exposure.
The brake shoe and lining assemblies should be replaced if the lining is worn to within 1/32 inch of rivet heads (riveted linings...
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1995 Ford Probe AUTOMOBILES
Ford Motor Co. Passenger Cars -> Component Locations -> 1993-97 Probe 2.5L Engine
Vehicle: 1995 Ford Probe GT 2.5 V6 GAS
Refer t...
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1995 Ford Probe AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 1995 Ford Probe GT 2.5 V6 GAS
When removing both Lefthand front wheel driveshaft and joint and Righthand front wheel driveshaft and joint, Transaxle Plugs T88C-7025-AH must be installed. Failure to use this tool can result in dislocation of differential side gears on 4EAT and MTX equipped vehicles. Should differential side gears become misaligned, differential will have to be removed from transaxle to re-align differential side gears.
- Raise and support vehicle.
- Remove lug nut and wheel and tire assembly.
- Carefully raise staked portion of front axle wheel hub retainer by using a small cape chisel and a ha...
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1995 Ford Probe AUTOMOBILES
Alternator, Replace
Vehicle: 1995 Ford Probe GT 2.5 V6 GAS
- Disconnect battery ground cable.
- Disconnect alternator wiring.
- Loosen drive belt tensioner center nut and adjusting bolt.
- Remove alternator upper mounting bolt.
- Raise and support vehicle.
- Remove righthand wheel splash screws, then remove righthand wheel splash guard.
- Remove alternator drive belt.
- Remove air conditioning compressor bolt, then position aside, if equipped.
- Loosen alternator lowe...
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1995 Ford Probe AUTOMOBILES
Ford Motor Co. Cars -> Check Engine Lamp/Malfunction Indicator Lamp (MIL)/Service Engine Soon Lamp -> 1995-97 Models -> EEC-IV -> EEC-V -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool -> PCM Reset Using Star Tester
Vehicle: 1995 Ford Probe SE 2.0 L4 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-IV system. A diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
EEC-IV
PCM Reset Using Star Tester
- Turn ignition Off.
- Perform required vehicle preparation and visual inspection.
- Connect Star teste...
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1995 Ford Probe AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 1995 Ford Probe SE 2.0 L4 GAS
Lower
- Drain cooling system into a suitable container.
- Reposition hose clamp from radiator using hose clamp pliers.
- Remove radiator outlet hose from radiator.
- Reposition hose clamp from water pump inlet pipe using hose clamp pliers.
- Remove radiator outlet hose from water pump inlet pipe and from vehicle.
- Reverse proc...
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1995 Ford Probe AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1995 Ford Probe SE 2.0 L4 GAS
- Loosen tensioner locknut.
- Loosen tensioner adjusti...
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1995 Ford Probe AUTOMOBILES
Component location diagrams for most 1995 Ford Probe cars and light trucks sold in the U.S. from 1990+.
 Fuel Filter Diagram for 1995 Ford Probe GT 2.5 V6 GASComponents on diagram: |
 I/P Switch Components Diagram for 1995 Ford Probe GT 2.5 V6 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1995 Ford Probe AUTOMOBILES
OEM drawn wiring diagrams for most 1995 Ford Probe cars and light trucks sold in the U.S.
 1995 Ford Probe SE 2.0 L4 GAS Wiring DiagramComponents on diagram: |
 1995 Ford Probe SE 2.0 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1995 Ford Probe AUTOMOBILES
OEM TSB listings for most 1995 Ford Probe cars and light trucks sold in the U.S. from 1985+.
|
Document: RECALL - CERTAIN 1992-2003 MODEL YEAR CARS AND TRUCKS - FUSED JUMPER HARNESS REPLACEMENT FOR VEHICLES SERVICED WITH AN INCOMPATIBLE FUSED JUMPER HARNESS Vehicle: 1995 Ford Probe GT 2.5 V6 GAS Auto Systems: |
|
Document: RECALL - 1992-2004 MULTIPLE VEHICLE LINES - SPEED CONTROL SYSTEM MODIFICATION Vehicle: 1995 Ford Probe GT 2.5 V6 GAS |
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1995 Ford Probe AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1995 Ford Probe cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1995 Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1995 Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1995 Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1995 Ford Probe SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1995 Ford Probe vehicle.
|
| Access the Complete guide! |
