Auto Parts Search
1990 Ford Probe CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1990 Ford Probe car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Probe automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
A/C & Cooling System Maintenance -> Ford Motor Co. -> Ford Probe
Vehicle: 1990 Ford Probe GT 2.2 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
DRUM BRAKES, FORD MOTOR CO. -> General Information -> SERVICE PRECAUTIONS
Vehicle: 1990 Ford Probe GL 2.2 L4 GAS
When working on or around brake assemblies, care must be taken to prevent breathing asbestos dust, as many manufacturers incorporate asbestos fibers in the production of brake linings. During routine service operations the amount of asbestos dust from brake lining wear is at a low level, due to a chemical break down during use and a few precautions will minimize exposure.Do not sand or grind brake linings unless suitable local exhaust ventilation equipment is used to prevent excessive asbestos exposure.
The brake shoe and lining assemblies should be replaced if the lining is ...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Ford Motor Co. Passenger Cars -> Fuel Pressure Relief -> 1989-97 Probe
Vehicle: 1990 Ford Probe LX 3.0 V6 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
When installing the fuel filter, ensure the flow arrow is facing in the proper direction.
After the battery has been disconnected and reconnected, some abnormal driveabil...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 1990 Ford Probe GL 2.2 L4 GAS
- Raise and support front of vehicle, then remove wheel and tire assembly.
- Remove underbody covers, then remove stabilizer bar link from control arm.
- Using a suitable chisel, raise staked portion of axle nut, then with brakes applied, loosen but do not remove nut.
- Remove lower control arm ball joint clamp bolt, then pry lower control arm downward and push inward on rotor to separate ball joint from steering knuckle. If removing Righthand halfshaft, remove dynamic damper from cylinder block.
- On models with manual transaxle, pull outward on steering knuckle and hub assembly to se...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Starter, Replace
Vehicle: 1990 Ford Probe GL 2.2 L4 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- On models equipped with manual transaxle, remove exhaust pipe bracket.
- On all models, remove transaxle to engine bracket.
- Remove intake manifold to engine bracket.
- Remove solenoid B+ terminal nut, then disconnect battery lead and S terminal electrical connector.
- Remove starter motor mounting bolts
- Remove starter motor from vehicle.
- Reverse procedure ...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Ford Motor Co. Cars -> Powertrain Malfunction Indicator ->
Vehicle: 1990 Ford Probe GT 2.2 L4 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected in the powertrain system. If the lamp remains On a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Powertrain Malfunction Indicator will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 1990 Ford Probe GL 2.2 L4 GAS
Lower
- Drain coolant into a suitable container.
- Loosen hose clamp connecting hose to radiator.
- Loosen hose clamp connecting hose to water pump inlet tube.
- Remove hose from vehicle.
- Reverse procedure...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1990 Ford Probe LX 3.0 V6 GAS
If the serpentine belt is to be reused, mark rotation direction on belt for installation reference. Failure to do so may result in belt noise.
- Remove plastic belt shield from power steering pump.
- Insert a 1/2 inch drive br...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1990 Ford Probe AUTOMOBILES
Component location diagrams for most 1990 Ford Probe cars and light trucks sold in the U.S. from 1990+.
 Underhood Lamp & Switches Diagram for 1990 Ford Probe GT 2.2 L4 GASComponents on diagram: |
 Rear Of Engine Diagram for 1990 Ford Probe GL 2.2 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1990 Ford Probe AUTOMOBILES
OEM drawn wiring diagrams for most 1990 Ford Probe cars and light trucks sold in the U.S.
 1990 Ford Probe GT 2.2 L4 GAS Wiring DiagramComponents on diagram: |
 1990 Ford Probe GT 2.2 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1990 Ford Probe AUTOMOBILES
OEM TSB listings for most 1990 Ford Probe cars and light trucks sold in the U.S. from 1985+.
|
Document: MERCON ATF IS BRING REPLACED BY MERCON V ATF AS A SERVICE FLUID Vehicle: 1990 Ford Probe GL 2.2 L4 GAS Auto Systems: |
|
Document: 3.OL 2V (VULCAN) REVISED OIL PAN GASKET REPLACEMENT PROCEDURE - NEW SERVICE KIT - SERVICE TIP - REVISED Vehicle: 1990 Ford Probe LX 3.0 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1990 Ford Probe AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1990 Ford Probe cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1990 Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1990 Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1990 Ford Probe cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1990 Ford Probe vehicle.
|
| Access the Complete guide! |
