Auto Parts Search
We have info for following modifications of 1990 Ford Probe
- 1990 Ford Probe GL 2.2 L4 GAS, CID:133, Fuel Injection, Aspiration:133, Engine VIN:, Desg:C
- 1990 Ford Probe GT 2.2 L4 GAS, CID:133, Fuel Injection, Aspiration:133, Engine VIN:, Desg:L
- 1990 Ford Probe LX 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:U
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Check Engine Lamp/Malfunction Indicator Lamp (MIL)/Service Engine Soon Lamp -> 1990-94 Models w/EEC-IV
Vehicle: 1990 Ford Probe LX 3.0 V6 GAS
This lamp should light when the ignition is turned On. After the engine is started, the lamp should go off, unless a fault condition is detected by the EEC-IV system. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when the stored codes are cleared from the EEC-IV system memory. After diagnosis and repair, the EEC-IV memory may be cleared of stored codes as follows:
- With ignition turned Off, connect a jumper wire between Self Test and Self Test Input (STI) connectors, Fig. . On Crown Victoria, Grand Marquis and Town Car models, the...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Service Interval Reminder -> Probe -> Electronic Instrument Cluster -> Vehicle Maintenance Monitor
Vehicle: 1990 Ford Probe GT 2.2 L4 GAS
Electronic Instrument Cluster
At 7500 mile intervals, a Service Check message will be displayed under the System Scanner nomenclature on the instrument cluster for 3 minutes after engine starts, Fig. . After performing the required interval service, reset the service interval by depressing and holding the Service reset button, located on the speed alarm keyboard, until three tones have sounded, Fig. .
Vehicle Maintenance Monitor
At 7500 mile intervals ...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Air Bag Warning Lamp ->
Vehicle: 1990 Ford Probe GT 2.2 L4 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned On as a bulb check. If the Air B...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Traction Control System Warning Lamp ->
Vehicle: 1990 Ford Probe GL 2.2 L4 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned On as a bulb check. If the warni...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Powertrain Malfunction Indicator ->
Vehicle: 1990 Ford Probe GL 2.2 L4 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected in the powertrain system. If the lamp remains On a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Powertrain Malfunction Indicator will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1990 Ford Probe AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1990 Ford Probe cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Cars -> Anti-Lock Brake Warning Lamp ->
Vehicle: 1990 Ford Probe GT 2.2 L4 GAS
This lamp should light when the ignition is turned On. It may light for as long as 30 seconds as a bulb and system inspect. If the lamp remains lit or lights while operating the vehicle, a fault condition in the anti-lock brake system is indicated. When the lamp is lit, turn ignition Off, then start...
CLICK HERE TO GET FULL ACCESS TO 1990 Ford Probe MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1990 Ford Probe vehicle. |
Access the Complete guide! |