Auto Parts Search
1992 Isuzu Pickup CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Isuzu REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1992 Isuzu Pickup car and truck
repair procedures including Isuzu engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Isuzu Pickup automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR 1992 Isuzu Pickup AUTOMOBILES
Imported Cars & Light Trucks & Vans -> 1991-92 -> Evacuating System
Vehicle: 1992 Isuzu Pickup Normal CAB 2.6 L4 GAS
The system must be completely discharged before evacuation. After discharging the system, keep low pressure gauge hose connected to low pressure test fitting and both manifold gauge valves closed.
- Connect high pressure gauge hose to vacuum pump, Fig. .
- Connect center manifold gauge hose to refrigerant source with tapping valve closed.
- Open high and low side gauge valves with vacuum pump operating.
- Continue to operate pump for approximately 15-20 minutes after low side gauge reaches 29 or more inches of vacuum. If the system has been left open for an...
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1992 Isuzu Pickup AUTOMOBILES
DISC BRAKES -> BRAKE PAD SERVICE -> AMIGO, PICKUP, RODEO & TROOPER -> FRONT -> IMPULSE & STYLUS -> Installation -> REAR -> Removal
Vehicle: 1992 Isuzu Pickup Normal CAB 2.3 L4 GAS
FRONT
IMPULSE & STYLUS
- Raise and support vehicle and remove front wheels.
- Remove upper and lower caliper mounting bolts, then remove caliper from disc, leaving brake hose attached. Do not let caliper hang by brake hose.
- Remove brake pads, with shims, from support bracket.
- Apply thin coat of suitable grease to rear face of new brake pad and install shim.
- Push in caliper piston and install pads.
- Install caliper assembly, then tighten retaining bolts to specification.
AMIGO, PICKUP, RODEO & TROOPER
Removal
- Raise vehicle and remove wheel assembly.
- Remove lock bolt from caliper.
- Posit...
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1992 Isuzu Pickup AUTOMOBILES
Isuzu -> Fuel Filter Replacement -> Amigo, Axiom, I-Mark, Impulse, Pickup, Rodeo, Stylus, Trooper & VehiCROSS w/Gasoline Engines -> Fuel System Pressure Relief -> Removal & Installation
Vehicle: 1992 Isuzu Pickup Normal CAB 2.3 L4 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
After the battery has been disconnected and reconnected, some abnormal driveability sympto...
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1992 Isuzu Pickup AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 1992 Isuzu Pickup Normal CAB 2.3 L4 GAS
- Raise and support vehicle.
- Mark flange for driveshaft alignment during installation.
- Remove differential side and transfer side bol...
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1992 Isuzu Pickup AUTOMOBILES
Starter, Replace
Vehicle: 1992 Isuzu Pickup Normal CAB 3.1 V6 GAS
- Disconnect battery ground cable at battery.
- Disconnect wiring from solenoid.
- Remove...
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1992 Isuzu Pickup AUTOMOBILES
Isuzu -> Intelligent Suspension Control (ISC) Indicator Lamp ->
Vehicle: 1992 Isuzu Pickup 2.3 L4 GAS
The Intelligent Suspension Control (ISC) indicator lamp will illuminate when the ignition switch is placed in the on position and should go off when the engine is started. If the lamp remains on or comes on while driving, a fault in the Intelligent Suspension Control is present. After diagnosis and repairs, then DTCs may be cleared as follows:
- Connect a ju...
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1992 Isuzu Pickup AUTOMOBILES
Heater Hose, Replace -> Bypass -> Inlet -> Outlet
Vehicle: 1992 Isuzu Pickup Normal CAB 2.3 L4 GAS
Inlet
- Disconnect negative cable from battery terminal.
- Drain engine coolant into a suitable container.
- Reposition hose clamp with suitable tool.
- Remove hose from heater core tube.
- Reposition hose clamp with suitable tool.
- Remove hose from thermostat housing.
- Reverse procedure to install.
Outlet
- Disconnect negative cable from battery terminal.
- Drain engine coolant into a suitable container.
- Reposition hose clamp with...
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1992 Isuzu Pickup AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1992 Isuzu Pickup Normal CAB 2.6 L4 GAS
- Rotate or lift the belt tensioner arm, using a suitable tool to relieve tension from dr...
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1992 Isuzu Pickup AUTOMOBILES
Component location diagrams for most 1992 Isuzu Pickup cars and light trucks sold in the U.S. from 1990+.
 Below Right Side Of I/P, At Kick Panel Diagram for 1992 Isuzu Pickup 2.3 L4 GASComponents on diagram: |
 I/P Harness Connector Locations Diagram for 1992 Isuzu Pickup 1 TON 2.6 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1992 Isuzu Pickup AUTOMOBILES
OEM drawn wiring diagrams for most 1992 Isuzu Pickup cars and light trucks sold in the U.S.
 1992 Isuzu Pickup Normal CAB 2.3 L4 GAS Wiring DiagramComponents on diagram: |
 1992 Isuzu Pickup 1 TON 2.6 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1992 Isuzu Pickup AUTOMOBILES
OEM TSB listings for most 1992 Isuzu Pickup cars and light trucks sold in the U.S. from 1985+.
|
Document: WARRANTY PROCEDURES Vehicle: 1992 Isuzu Pickup 2.3 L4 GAS Auto Systems: |
|
Document: MANUAL TRANSMISSION OPERATING CHARACTERISTICS - REVISED Vehicle: 1992 Isuzu Pickup 2.3 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1992 Isuzu Pickup AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1992 Isuzu Pickup cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1992 Isuzu Pickup cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1992 Isuzu Pickup cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1992 Isuzu Pickup cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1992 Isuzu Pickup SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1992 Isuzu Pickup vehicle.
|
| Access the Complete guide! |
