Auto Parts Search
1993 Ford Festiva CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1993 Ford Festiva AUTOMOBILES
General Service Domestic Vehicles -> 1992-93 -> Discharging System
Vehicle: 1993 Ford Festiva L 1.3 L4 GAS
R-134a systems require the use of special service equipment designed specifically for R-134a systems. R-12 servicing equipment cannot be used on R-134a systems.
Refrigerant-12 recovery stations cannot be used on Refrigerant-134a systems. A separate recovery station must be used on R-134a systems. The refrigerants are not compatible and will contaminate the R-12 recovery station.
The use of refrigerant recovery and recycling stations allows the recovery and reuse of refrigerant after contaminants and moisture have been removed.
When using a recovery or recycli...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Ford Festiva AUTOMOBILES
Disc Brakes -> Front Disc Brakes -> INSPECTION
Vehicle: 1993 Ford Festiva L 1.3 L4 GAS
Remove wheels and inspect brake disc, caliper and linings. The wheel bearings should be inspected at this time and repacked if necessary. Do not get any grease on the linings.
If the caliper is cracked or fluid leakage through the casting is evident, it must be replaced as a unit.
Should it become necessary to remove the caliper when installing new parts, clean all parts in alcohol, then wipe dry using lint-free cloths. Using an air hose, blow out drilled passages and bores. Check dust boots for punctures or tears. If punctures or tears are evident, install new boots during assembly.
In...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1993 Ford Festiva AUTOMOBILES
Ford Motor Co. Passenger Cars -> Fuel Pressure Relief -> 1988-93 Aspire & Festiva
Vehicle: 1993 Ford Festiva L 1.3 L4 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
When installing the fuel filter, ensure the flow arrow is faci...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 Ford Festiva AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 1993 Ford Festiva L 1.3 L4 GAS
- Raise and support vehicle.
- Drain transmission fluid from transaxle.
- Remove front wheel and tire assemblies.
- Use small cape chisel to carefully raise staked portion of front axle wheel hub retainer.
- While applying brakes, loosen but do not remove front axle wheel hub retainer.
- Remove ball joint clamp bolt and nut.
- Carefully pry down on front suspension lower arm to separate ball joint from front wheel knuckle.
- Separate driveshaft and joint from transaxle gradually. If driveshaft is yanked from transaxle, d...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1993 Ford Festiva AUTOMOBILES
Starter, Replace -> Automatic Transaxle -> Manual Transaxle
Vehicle: 1993 Ford Festiva GL 1.3 L4 GAS
Automatic Transaxle
- Disconnect battery ground cable.
- Remove upper starter motor mounting bolts.
- Raise and support vehicle.
- Remove manifold to cylinder block bracket bolts, then bracket.
- Remove mounting bracket to support bracket bolt.
- Remove support bracket.
- Remove nuts and washers that secure mounting bracket to starter motor.
- Disconnect the B+ and S terminal connectors at starter solenoid.
- Remove lower starter motor mounting bolt.
- Remove starter motor from vehicle.
- ...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1993 Ford Festiva AUTOMOBILES
Ford Motor Co. Cars -> Air Bag Warning Lamp ->
Vehicle: 1993 Ford Festiva GL 1.3 L4 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned On as a bulb check. If the Air B...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1993 Ford Festiva AUTOMOBILES
Heater Hose, Replace -> Bypass -> Inlet -> Outlet
Vehicle: 1993 Ford Festiva GL 1.3 L4 GAS
Inlet
- Drain cooling system into a suitable container.
- Reposition heater hose inlet clamp at cylinder head fitting using hose clamp pliers.
- Remove heater inlet hose from cylinder head fitting.
- Reposition heater core inlet hose clamp at heater core using hose clamp pliers.
- Remove hose from vehicle.
- Reverse procedure to install.
Outlet
- Drain cooling system into a suitable container.
- Reposition heater hose outlet clamp at lower radiator hose using hose clamp...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1993 Ford Festiva AUTOMOBILES
Serpentine Drive Belt, Replace -> Air Conditioning with Power Steering -> Air Conditioning without Power Steering -> Alternator
Vehicle: 1993 Ford Festiva L 1.3 L4 GAS
Air Conditioning without Power Steering
- Disconnect battery ground cable from battery.
- Loosen drive belt idler pulley nut.
- Loosen idler pulley adjusting bolt until there is enough slack to remove A/C compressor drive belt.
- Remove A/C compressor drive belt from drive belt idler pulley.
- Clean and inspect belt surfaces of all pulleys.
- Reverse procedure to install, noting the following:
- Torque drive belt idler pulley nut to 27 to 38 ft. lbs.
Air Conditioning with Power Steering
- Disconnect battery ground cable from battery.
- Remove air cleaner intake tube and engine air cleaner.
- Lo...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1993 Ford Festiva AUTOMOBILES
Component location diagrams for most 1993 Ford Festiva cars and light trucks sold in the U.S. from 1990+.
Behind I/P Diagram for 1993 Ford Festiva L 1.3 L4 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1993 Ford Festiva AUTOMOBILES
OEM drawn wiring diagrams for most 1993 Ford Festiva cars and light trucks sold in the U.S.
1993 Ford Festiva GL 1.3 L4 GAS Wiring Diagram Components on diagram: |
1993 Ford Festiva L 1.3 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1993 Ford Festiva AUTOMOBILES
OEM TSB listings for most 1993 Ford Festiva cars and light trucks sold in the U.S. from 1985+.
Document: RECALL - CERTAIN 1992-2003 MODEL YEAR CARS AND TRUCKS - FUSED JUMPER HARNESS REPLACEMENT FOR VEHICLES SERVICED WITH AN INCOMPATIBLE FUSED JUMPER HARNESS Vehicle: 1993 Ford Festiva L 1.3 L4 GAS Auto Systems: |
Document: RECALL - 1992-2004 MULTIPLE VEHICLE LINES - SPEED CONTROL SYSTEM MODIFICATION Vehicle: 1993 Ford Festiva L 1.3 L4 GAS |
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1993 Ford Festiva AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1993 Ford Festiva cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1993 Ford Festiva cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1993 Ford Festiva cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1993 Ford Festiva cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Festiva SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1993 Ford Festiva vehicle. |
Access the Complete guide! |