Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1993 Ford Probe car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1993 Ford Probe automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1993 Ford Probe
- 1993 Ford Probe GT 2.5 V6 GAS, CC:2450, CID:152, Fuel Injection, Aspiration:152, Engine VIN:, Desg:B
- 1993 Ford Probe SE 2.0 L4 GAS, CC:1989, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:A
BRAKE SERVICE PROCEDURES FOR 1993 Ford Probe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Ford Probe cars and light trucks from 1990+.
Disc Brakes -> Rear Disc Brakes & Parking Brakes -> Tightening Specifications
Vehicle: 1993 Ford Probe SE 2.0 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Probe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Ford Probe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Ford Probe cars and light trucks from 1990+.
Disc Brakes -> Rear Disc Brakes & Parking Brakes -> Caliper Service -> Assemble -> CALIPER OVERHAUL -> CALIPER, REPLACE -> CAPRI -> Cleaning & Inspection -> CONTINENTAL, COUGAR, MARK VIII & THUNDERBIRD -> CROWN VICTORIA, GRAND MARQUIS & TOWN CAR -> Disassemble -> ESCORT & TRACER -> Inspection -> Installation -> MARK VII -> MUSTANG -> PROBE -> Removal -> SABLE & TAURUS
Vehicle: 1993 Ford Probe SE 2.0 L4 GAS
CALIPER, REPLACE
MARK VII
Removal
- Raise and support vehicle, then remove tire and wheel assemblies.
- Disconnect fitting on rear brake tube from hose end fitting at frame mounted bracket. Plug end of brake tube to prevent fluid loss and entry of dirt.
- Remove horse shoe retaining clip from hose fitting and disengage hose from bracket.
- Disconnect parking cable from lever, Fig. , using care to avoid kinking or cutting cable or return spring, then remove screw from caliper key, Fig. , then remove caliper locating pins.
- Slide caliper key and support spring from anchor plate, Fig. , noting the...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Probe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Ford Probe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Ford Probe cars and light trucks from 1990+.
Drum Brakes -> Type 8 -> Brake Service -> INSTALLATION -> REMOVAL
Vehicle: 1993 Ford Probe SE 2.0 L4 GAS
REMOVAL
- Raise and support vehicle, then remove wheel and tire assembly.
- Remove grease hub cap.
- Remove brake drum screws, then the drum, Fig. .
- Remove wheel hub as described in specific chassis section.
- Remove brake shoe hold down springs, Fig. , using screwdriver to push in and twist spring to disengage it from pin.
- Remove parking brake rear cable and conduit from parking brake cable anchor plate. Remove brake shoe retracting spring.
- Remove trailing brake shoe and lining from rear brake strut and quadrant, then the leading brake shoe and lining.
INSTALLATION
- If brake shoes and linings are ...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Probe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Ford Probe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Ford Probe cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Disassemble -> Inspection -> MASTER CYLINDER OVERHAUL -> Overhaul -> WHEEL CYLINDERS
Vehicle: 1993 Ford Probe SE 2.0 L4 GAS
MASTER CYLINDER OVERHAUL
Disassemble
- Clean outside of master cylinder thoroughly. Drain brake fluid from master cylinder.
- Remove stop bolt and pressure control valves, if equipped.
- Using a screwdriver, carefully pry up on reservoir and remove it from master cylinder body.
- Remove fluid control valve, if equipped.
- Depress primary piston and remove snap ring from retaining groove at open end of bore.
- Remove primary and secondary piston assemblies from master cylinder. If secondary piston does not come out, apply air pressure to secondary outlet port to remove.
Inspection
When disassembled...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Probe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Ford Probe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Ford Probe cars and light trucks from 1990+.
Hydraulic Brake Systems -> Hydraulic Brake System Specifications
Vehicle: 1993 Ford Probe SE 2.0 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Probe BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Ford Probe AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Ford Probe cars and light trucks from 1990+.
Hydraulic Brake Systems -> Description -> BRAKE DISTRIBUTION VALVE & SWITCH -> BRAKE WARNING LIGHT SWITCHES -> COMBINATION VALVE -> Description -> DIAGONALLY SPLIT SYSTEMS -> Failure Warning Switch -> FRONT & REAR SPLIT SYSTEMS -> Metering Valve -> Proportioner Or Pressure Control Valves -> PROPORTIONING VALVE -> Testing -> Testing Warning Light System
Vehicle: 1993 Ford Probe GT 2.5 V6 GAS
FRONT & REAR SPLIT SYSTEMS
When the brake pedal is depressed, both the primary (front brake) and the secondary (rear brake) master cylinder pistons are moved simultaneously to exert hydraulic fluid pressure on their respective independent hydraulic systems. The fluid displacement of the master cylinder is proportioned to fulfill the requirements of each of the two independent hydraulic brake systems, Fig. .
If a failure of a rear (secondary) brake system should occur, initial brake pedal movement causes the unrestricted secondary piston to bottom in the master cylinder bore. Primary p...
CLICK HERE TO GET FULL ACCESS TO 1993 Ford Probe BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1993 Ford Probe vehicle.
|
| Access the Complete guide! |
