Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1993 Mazda Protege car and truck
repair procedures including Mazda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1993 Mazda Protege automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1993 Mazda Protege
- 1993 Mazda Protege LX 1.8 L4 GAS, CC:1839, Fuel Injection
- 1993 Mazda Protege DX 1.8 L4 GAS, CC:1839, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 1993 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mazda Protege cars and light trucks from 1990+.
POWER BRAKE UNITS -> TROUBLESHOOTING -> Check Valve -> Function Check -> Load Test
Vehicle: 1993 Mazda Protege DX 1.8 L4 GAS
Function Check
- Stop engine and depress brake pedal a few times to relieve vacuum.
- With pedal depressed, start engine. After starting engine, pedal should move down slightly. If so, unit is functioning.
- After engine has run two minutes, turn it off. Depress pedal with normal force.
- If the first pedal stroke is long and gets shorter with subsequent strokes, the unit is operating. If a problem is found, inspect check valve, vacuum hose and installation. Repair if necessary and check again.
- Start engine and depress pedal with usual force.
- Stop engine with pedal still depressed. Hold pedal...
CLICK HERE TO GET FULL ACCESS TO 1993 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mazda Protege cars and light trucks from 1990+.
DISC BRAKES -> ADJUSTMENTS -> 929 -> Except Millenia, RX-7 & 929 -> Millenia -> Parking Brake -> RX-7
Vehicle: 1993 Mazda Protege LX 1.8 L4 GAS
Parking Brake
Except Millenia, RX-7 & 929
- Ensure parking brake is completely released.
- Block front wheels, then raise and support rear of vehicle.
- Adjust parking brake lever screw or nut until wheels are locked when the brake lever is pulled 5-7 notches.
Millenia
- Adjust parking brake shoe clearance as follows:
- Working through rotor access hole, turn adjuster 3 to 5 notches in direction opposite arrow on rotor to set shoe clearance to approximately .013 inch.
- Rotate rotor by hand to ensure parking brake shoes do not drag, then install access hole plug.
- Settle parking brake shoes as follows:
- Mo...
CLICK HERE TO GET FULL ACCESS TO 1993 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mazda Protege cars and light trucks from 1990+.
HYDRAULIC BRAKE SYSTEMS -> BRAKE SYSTEM BLEED -> Except Navajo & 1994-96 Pickups -> Navajo & 1994-96 Pickups
Vehicle: 1993 Mazda Protege LX 1.8 L4 GAS
Except Navajo & 1994-96 Pickups
- Raise and support vehicle with jack stands.
- Fill reservoir with brake fluid, ensure reservoir is at least half full at all times during bleeding procedure.
- After removing bleeder cap, connect one end of transparent vinyl tube to bleeder and place other end in a clean, clear container that is half full with brake fluid.
- One person should depress pedal a few times, then hold the pedal depressed.
- A second person should loosen the bleeder screw and drain fluid, then retighten screw to specifications.
- Repeat steps 4 and 5 until there are no more air bubbl...
CLICK HERE TO GET FULL ACCESS TO 1993 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mazda Protege cars and light trucks from 1990+.
DISC BRAKES -> PARKING BRAKE SERVICE -> 929 -> Adjustment -> Millenia -> Replacement
Vehicle: 1993 Mazda Protege LX 1.8 L4 GAS
Replacement
929
- Raise and support vehicle and remove rear wheel assembly.
- Remove caliper attaching bolts, then the caliper, leaving brake hose attached, and position caliper out of way.
- Remove disc plate attaching screws and the disc plate, Fig. . If disc plate is difficult to remove, remove dust cap, insert screwdriver into hole and turn adjuster to increase shoe clearance.
- Remove upper and lower return springs, then the front and rear hold pins.
- Remove brake shoes, then separate adjuster and operating lever assembly from shoes.
- Check inside of disc plate for scratching and unev...
CLICK HERE TO GET FULL ACCESS TO 1993 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mazda Protege cars and light trucks from 1990+.
DISC BRAKES -> BRAKE PAD SERVICE -> 1993 -> 1994-96 -> 929 -> Front -> Installation -> Miata -> Miata & MX-3 -> Millenia -> MPV & 929 -> MX-3 -> MX-6 & 626 -> Navajo -> Pickups -> Protege & 323 -> Rear -> Removal -> RX-7
Vehicle: 1993 Mazda Protege DX 1.8 L4 GAS
Front
Miata
- Raise and support front of vehicle, then remove front wheels.
- Remove parts in order as shown in Fig. , noting the following:
- After removing lower lock bolt, rotate caliper upward and support with rope.
- Reverse procedure to install, noting the following.
- Push the piston inward using piston pushing tool No. 490221600C, or equivalent, then install new pads.
Millenia
Brake pads should be replaced as a set if lining thickness is below .08 inch on any pad.
- Raise and support vehicle, then remove wheel and caliper lower mounting bolt.
- Pivot caliper upward off rotor, Figs. and . Do ...
CLICK HERE TO GET FULL ACCESS TO 1993 Mazda Protege BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mazda Protege AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mazda Protege cars and light trucks from 1990+.
POWER BRAKE UNITS -> POWER BRAKE UNIT SERVICE -> Overhaul -> Replacement
Vehicle: 1993 Mazda Protege LX 1.8 L4 GAS
Replacement
- Remove master cylinder as described in "Hydraulic Brake Systems" .
- Remove clutch pipe holder, if equipped, then disconnect vacuum hose from power brake unit.
- Disconnect pushrod fork from brake pedal and remove power brake unit from vehicle.
- Reverse procedure to install, noting the following:
- On all models except Navajo & 1994-95 Pickups, torque booster bolts to 14-17 ft. lbs.
- On Navajo & 199...
CLICK HERE TO GET FULL ACCESS TO 1993 Mazda Protege BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
