Auto Parts Search
We have info for following modifications of 1993 Mitsubishi Mighty MAX
- 1993 Mitsubishi Mighty MAX 2.4 L4 GAS, CC:2351, Fuel Injection, Engine VIN:, Desg:G
- 1993 Mitsubishi Mighty MAX 3.0 V6 GAS, CC:2972, CID:181, Fuel Injection, Aspiration:181, Engine VIN:, Desg:H
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Mighty MAX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Mighty MAX cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Bleed -> Master Cylinder Bleed
Vehicle: 1993 Mitsubishi Mighty MAX 2.4 L4 GAS
Master Cylinder Bleed
- If master cylinder has been replaced or overhauled and reservoir is empty, proceed as follows:
- Fill reservoir with clean brake fluid, then disconnect brake lines at master cylinder.
- Depress pedal slowly and hold pedal in depressed position.
- Place fingers over outlet port, then release brake pedal.
- Repeat above steps several times. Refill reservoir suitable brake fluid.
Hydraulic System Bleed
The hydraulic brake system must be bled if air has entered the system. This condition may be precipitated by low fluid level, a hydraulic fluid leak, the opening of a hydra...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Mighty MAX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Mighty MAX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Mighty MAX cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> 1995-96 Eclipse -> Diamante -> Except Diamante & 1995-96 Eclipse -> Installation -> Master Cylinder -> Removal -> Wheel Cylinder
Vehicle: 1993 Mitsubishi Mighty MAX 3.0 V6 GAS
Master Cylinder
Except Diamante & 1995-96 Eclipse
- Disconnect brake fluid sensor electrical connector from master cylinder reservoir.
- Position a drain pan under master cylinder.
- On models with separately mounted reservoir, disconnect reservoir hoses from the master cylinder.
- On all models, disconnect brake lines from the master cylinder. Plug all lines and fittings.
- Remove master cylinder to brake booster attaching nuts.
- Pull master cylinder outward and away from brake booster.
- Reverse procedure to install, noting the following:
- Prior to master cylinder installation,...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Mighty MAX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Mighty MAX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Mighty MAX cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting -> Except Pickup -> General Malfunction Diagnosis -> Pickup -> Transient Malfunction Diagnosis
Vehicle: 1993 Mitsubishi Mighty MAX 3.0 V6 GAS
General Malfunction Diagnosis
Except Pickup
Problems related to the Anti-Lock Brake System (ABS) can generally be classified as electrical or hydraulic.
For problems in the electrical system, a self-diagnostic function is built into the Electronic Control Unit (ECU), allowing the ABS warning lamp to illuminate as a warning to the driver in the event of an abnormality. In this instance, inspections can be performed with a voltmeter, Multi-Use Tester (MUT), oscilloscope or the ABS warning lamp.
Problems with the hydraulic system can be located in the same manner as ordinary brakes. It...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Mighty MAX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Mighty MAX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Mighty MAX cars and light trucks from 1990+.
Power Brake Units -> Troubleshooting
Vehicle: 1993 Mitsubishi Mighty MAX 3.0 V6 GAS
- Run engine for two minutes, then turn engine off. Depress brake pedal slowly several times.
- Pedal should go down farther the first time and rise gradually the second and third time, Fig. . If pedal height remains the same booster is faulty.
- With engine off, depress brake pedal several times, Fig. . There should be ...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Mighty MAX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Mighty MAX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Mighty MAX cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Cleaning & Inspection -> Disassemble -> Master Cylinder -> Overhaul -> Wheel Cylinder
Vehicle: 1993 Mitsubishi Mighty MAX 3.0 V6 GAS
Master Cylinder
Overhaul
- Disassemble master cylinder in numbered sequence shown, Figs. and . Note the position of all parts as they are removed for proper installation.
- On models equipped with attached reservoir master cylinder, remove reservoir screw and cap, brake fluid sensor, float, then the reservoir, Fig. .
- On models equipped with separately mounted reservoir, remove nipple, Fig. .
- Use a wooden stick or dowel to depress primary piston into cylinder bore.
- On all models except Precis, with pushrod depressed, remove piston stopper bolt, the...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Mighty MAX BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Mitsubishi Mighty MAX AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Mitsubishi Mighty MAX cars and light trucks from 1990+.
Anti-lock Brakes -> Diagnosis & Testing -> 1993-95 -> 1994-96 Galant -> 1995 Eclipse -> 1995-96 Eclipse AWD -> 1995-96 Eclipse FWD & 1996 3000GT -> 1996 -> 1996 3000GT -> 1996 Eclipse -> Accessing Diagnostic Trouble Codes -> AWD Models -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Interpretation -> Diamante -> Diamante & Mirage -> Eclipse, Expo & 3000GT -> Expo, 1993 Galant, 1993-94 Eclipse & 1993-95 3000GT -> FWD Models -> Galant & Montero -> Less Multi-Use Tester (MUT) -> Mirage -> Montero -> Pickup -> Using ABS Warning Lamp -> Using Multi-Use Tester (MUT) -> Using Scan Tool -> Using Voltmeter -> With Multi-Use Tester (MUT)
Vehicle: 1993 Mitsubishi Mighty MAX 3.0 V6 GAS
Accessing Diagnostic Trouble Codes
Expo, 1993 Galant, 1993-94 Eclipse & 1993-95 3000GT
Using ABS Warning Lamp
Refer to Figs. through for ABS warning lamp diagnostic procedures.
Using Multi-Use Tester (MUT)
- With ignition switch in Off position, connect MUT through adapter harness, then turn ignition switch to On position and select ABS. In MUT mode, ABS does not function.
- The ABS warning lamp should light when in MUT mode. If access is not possible, check ECU power circuit and harness between ECU and diagnosis check terminal.
- Read and record diagnostic trouble code output...
CLICK HERE TO GET FULL ACCESS TO 1993 Mitsubishi Mighty MAX BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1993 Mitsubishi Mighty MAX vehicle. |
Access the Complete guide! |