Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1994 Chevrolet Corvette car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1994 Chevrolet Corvette automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1994 Chevrolet Corvette
- 1994 Chevrolet Corvette 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:P
- 1994 Chevrolet Corvette ZR-1 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:J
BRAKE SERVICE PROCEDURES FOR 1994 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Chevrolet Corvette cars and light trucks from 1990+.
Power Brake Units -> Description -> AC-DELCO SINGLE DIAPHRAGM TYPE -> AC-DELCO TANDEM DIAPHRAGM TYPE -> BCIA SINGLE & TANDEM DIAPHRAGM TYPE
Vehicle: 1994 Chevrolet Corvette ZR-1 5.7 V8 GAS
AC-DELCO TANDEM DIAPHRAGM TYPE
This unit utilizes a vacuum power chamber, consisting of a front and rear shell, housing divider, front and rear diaphragm, plate assemblies, hydraulic pushrod and a diaphragm return spring, Figs. and .
The unit operates in much the same manner as the single diaphragm unit described previously. The diaphragm and plate assemblies utilize the pressure differential between the engine intake manifold vacuum and atmospheric pressure to assist in braking.
AC-DELCO SINGLE DIAPHRAGM TYPE
The AC-Delco power booster assembly, Fig. is located along the bulkhead in ...
CLICK HERE TO GET FULL ACCESS TO 1994 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Single Piston Rear Disc Brake -> Caliper Service -> CALIPER ASSEMBLE -> CALIPER DISASSEMBLE -> CALIPER INSTALLATION -> CALIPER REMOVAL
Vehicle: 1994 Chevrolet Corvette 5.7 V8 GAS
CALIPER REMOVAL
- Disable parking brake automatic adjuster as follows:
- Working from inside vehicle, remove driver seat cushion, then the parking brake lever cover screws and cover.
- Using .080 inch gauge wire, fabricate a tool to disengage drive pawl from sector, Fig. .
- Using tool mentioned above, disengage drive pawl from sector, then insert a nail through anchor plate to keep drive pawl in disengaged position.
- Pull up on lever until it aligns with pawl, then depress button until lever is fully downward.
- Visually inspect that anchor plate is fully against stud. If not, repeat procedure ...
CLICK HERE TO GET FULL ACCESS TO 1994 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Single Piston Rear Disc Brake -> Brake Pad Service -> INSTALLATION -> REMOVAL
Vehicle: 1994 Chevrolet Corvette 5.7 V8 GAS
REMOVAL
- Remove 2/3 of the total brake fluid capacity from master cylinder reservoir.
- Raise and support vehicle, then remove tire and wheel assembly.
- Install two wheel retaining nuts to retain rotor in position.
- Position one end of a suitable C-clamp against inlet fitting bolt, and the other end against outboard shoe and lining, then tighten clamp as shown, Fig. , until piston fully bottoms in caliper bore.
- Remove upper guide pin bolt and discard.
- Loosen lower guide pin bolt, then pivot caliper downward on the lower guide pin bolt to expose the shoe & lining assemblies. Use care to a...
CLICK HERE TO GET FULL ACCESS TO 1994 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Brake System Bleed
Vehicle: 1994 Chevrolet Corvette ZR-1 5.7 V8 GAS
Pressure bleeding is recommended for all hydraulic disc brake systems.
The disc brake hydraulic system can be bled manually or with pressure bleeding equipment. On vehicles with disc brakes the brake pedal will require more pumping and frequent checking of fluid level in master cylinder during bleeding oper...
CLICK HERE TO GET FULL ACCESS TO 1994 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Single Piston Rear Disc Brake -> Brake System Bleed
Vehicle: 1994 Chevrolet Corvette 5.7 V8 GAS
Pressure bleeding is recommended for all hydraulic disc brake systems.
The disc brake hydraulic system can be bled manually or with pressure bleeding equipment. On vehicles with disc brakes the brake pedal will require more pumping and frequent checking of fluid level in master cylinder during bleeding oper...
CLICK HERE TO GET FULL ACCESS TO 1994 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1994 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1994 Chevrolet Corvette cars and light trucks from 1990+.
Power Brake Units -> General Service
Vehicle: 1994 Chevrolet Corvette ZR-1 5.7 V8 GAS
Two basic types of power assist mechanisms are used: vacuum assist diaphragm assemblies, which use engine vacuum or, in some cases vacuum pressure developed by an external vacuum pump. The second type is a hydraulic pressure assist mechanism, which use pressure developed by an external pump (usually the power steering pump). Both systems act to increase the force exerted on the master cylinder piston by the operator. This in turn increases the hydraulic pressure delivered to the wheel cylinders, while decreasing driver effort necessary to obtain acceptable stopping performance.
V...
CLICK HERE TO GET FULL ACCESS TO 1994 Chevrolet Corvette BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
