Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1996 Chevrolet Corvette car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1996 Chevrolet Corvette automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1996 Chevrolet Corvette
- 1996 Chevrolet Corvette 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:P
- 1996 Chevrolet Corvette 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:5
BRAKE SERVICE PROCEDURES FOR 1996 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Chevrolet Corvette cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Bleed Sequence -> Hydraulic System Flush -> Manual -> Pressure
Vehicle: 1996 Chevrolet Corvette 5.7 V8 GAS
Manual
Pressure bleeding is recommended for all hydraulic systems. However, if a pressure bleeder is unavailable, use the following procedure. Brake fluid damages painted surfaces. Immediately clean any spilled fluid.
- Remove vacuum reserve by pumping brakes several times with engine off.
- Fill master cylinder reservoir with clean brake fluid. Check fluid level often during bleeding procedure; do not let reservoir fall below half full.
- If necessary, bleed master cylinder as follows:
- Disconnect master cylinder forward brake line connection until fluid flows from reservoir. Reconnect ...
CLICK HERE TO GET FULL ACCESS TO 1996 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Description
Vehicle: 1996 Chevrolet Corvette 5.7 V8 GAS
This front caliper, Fig. , consists of dual pistons and an aluminum housing which is suspended on the shoe and lining assemblies. Hydraulic pressure, created by applying force to the brake pedal, acts equally against the pistons and the botto...
CLICK HERE TO GET FULL ACCESS TO 1996 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Chevrolet Corvette cars and light trucks from 1990+.
Anti-lock Brakes -> Corvette -> System Service -> Brake Pressure Modulator Valve (BPMV) -> Brake System Bleed -> Component Replacement -> Electronic Brake Traction Control Module (EBTCM) -> Front -> Hydraulic System Flush -> Lateral Acceleration Switch (Accelerometer) -> Manual Bleed -> Pressure Bleed -> Rear -> Wheel Speed Sensor -> Wiring Harness
Vehicle: 1996 Chevrolet Corvette 5.7 V8 GAS
When a diagnostic test refers to removing, replacing or checking a component for proper mounting, refer to "Component Replacement."
After all diagnosis and repairs are completed, road test the vehicle to ensure proper ABS operation and that the SERVICE ABS light does not illuminate. If the Tech 1 was used for diagnosis, disconnect it from the Assembly Line Diagnostic Link (ALDL) connector and turn the ignition switch to the Off position before road testing the vehicle. This is required to reset the EBTCM, as it is disabled during Tech 1 diagnostics and does not reset until serial da...
CLICK HERE TO GET FULL ACCESS TO 1996 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Chevrolet Corvette cars and light trucks from 1990+.
Power Brake Units -> Adjustments -> AC-Delco Single Diaphragm Type -> AC-Delco Tandem Diaphragm Type -> Air Method -> Brake Pedal -> Gauge Method -> Pushrod -> Toyota/GM Single Diaphragm Type
Vehicle: 1996 Chevrolet Corvette 5.7 V8 GAS
Brake Pedal
Toyota/GM Single Diaphragm Type
- With engine running and brake pedal in rest position, measure distance between face of pedal and floor mat.
- If distance is not 5.79-6.18 inches, adjust pedal height as follows:
- Remove left lower instrument panel trim section and air duct.
- Loosen stop lamp switch sufficiently to gain clearance for pedal adjustment.
- Loosen locknut and rotate pedal pushrod as needed to obtain specified pedal height, then tighten locknut.
- Adjust position of brake light switch so that plunger lightly contacts pedal stopper and brake lamps are off when pedal is release...
CLICK HERE TO GET FULL ACCESS TO 1996 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Single Piston Rear Disc Brake -> Caliper Service -> Caliper Assemble -> Caliper Disassemble -> Caliper Installation -> Caliper Removal
Vehicle: 1996 Chevrolet Corvette 5.7 V8 GAS
Caliper Removal
- Disable parking brake automatic adjuster as follows:
- Working from inside vehicle, remove driver seat cushion, then the parking brake lever cover screws and cover.
- Using .080 inch gauge wire, fabricate a tool to disengage drive pawl from sector, Fig. .
- Using tool mentioned above, disengage drive pawl from sector, then insert a nail through anchor plate to keep drive pawl in disengaged position.
- Pull up on lever until it aligns with pawl, then depress button until lever is fully downward.
- Visually inspect that anchor plate is fully against stud. If not, repeat procedure ...
CLICK HERE TO GET FULL ACCESS TO 1996 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1996 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1996 Chevrolet Corvette cars and light trucks from 1990+.
Anti-lock Brakes -> Corvette -> System Service -> Brake Pressure Modulator Valve (BPMV) -> Brake System Bleed -> Component Replacement -> Electronic Brake Traction Control Module (EBTCM) -> Front -> Hydraulic System Flush -> Lateral Acceleration Switch (Accelerometer) -> Manual Bleed -> Pressure Bleed -> Rear -> Wheel Speed Sensor -> Wiring Harness
Vehicle: 1996 Chevrolet Corvette 5.7 V8 GAS
When a diagnostic test refers to removing, replacing or checking a component for proper mounting, refer to "Component Replacement."
After all diagnosis and repairs are completed, road test the vehicle to ensure proper ABS operation and that the SERVICE ABS light does not illuminate. If the Tech 1 was used for diagnosis, disconnect it from the Assembly Line Diagnostic Link (ALDL) connector and turn the ignition switch to the Off position before road testing the vehicle. This is required to reset the EBTCM, as it is disabled during Tech 1 diagnostics and does not reset until serial da...
CLICK HERE TO GET FULL ACCESS TO 1996 Chevrolet Corvette BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
