Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1996 Ford Windstar car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1996 Ford Windstar automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1996 Ford Windstar
- 1996 Ford Windstar 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:U
- 1996 Ford Windstar 3.8 V6 GAS, CID:232, Fuel Injection, Aspiration:232, Engine VIN:, Desg:4
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Low Coolant Lamp ->
Vehicle: 1996 Ford Windstar 3.0 V6 GAS
This lamp should light when engine coolant level in the radiator drops below a predetermined le...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Traction Control System Warning Lamp ->
Vehicle: 1996 Ford Windstar 3.0 V6 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned On as a bulb check. If the warni...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Fuel Cap Lamp ->
Vehicle: 1996 Ford Windstar 3.0 V6 GAS
The Check Fuel Cap Lamp will illuminate momentarily when the ignition switch is placed in the On position as a bulb check. If the lamp remains...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 1996 Ford Windstar 3.8 V6 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Low Fuel Level Warning Lamp ->
Vehicle: 1996 Ford Windstar 3.0 V6 GAS
When fuel level drops below a predetermined level, the CHECK GAUGE indicator should light. The CHECK GAUGE indicator shoul...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1996 Ford Windstar AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 1996 Ford Windstar cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Engine Lamp -> 1993-97 -> Continuous Memory -> EEC -> EEC IV -> EEC V -> Except Malfunction Indicator Lamp (MIL) -> Keep Alive Memory (KAM) -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> Malfunction Indicator Light -> PCM Reset Using Generic Scan Tool
Vehicle: 1996 Ford Windstar 3.0 V6 GAS
EEC
Except Malfunction Indicator Lamp (MIL)
When using NGS tool No. 007-00500, or equivalent, select Diagnostic Test Mode Results, then press CLEAR or disconnect battery ground cable. Codes will be erased from back-up memory after 24 hours.
Malfunction Indicator Light
- Activate diagnostic test mode.
- Disconnect diagnostic connector.
- Jump BL/W and GY/BL wires using suitable jumper wire.
- Wait about two seconds.
- Remove jumper wire and reconnect diagnostic connector.
- MIL will stay on, and codes will be erased.
EEC IV
Continuous Memory
This lamp should light when the ignition is turned On. After the engin...
CLICK HERE TO GET FULL ACCESS TO 1996 Ford Windstar MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1996 Ford Windstar vehicle.
|
| Access the Complete guide! |
