Auto Parts Search
BRAKE SERVICE PROCEDURES FOR 1997 Mazda B4000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda B4000 cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> B-Series -> Front -> Miata -> Millenia -> MPV -> MX-6 & 626 -> Protege -> Rear -> Replacement -> Service -> Tribute
Vehicle: 1997 Mazda B4000 4.0 V6 GAS
Front
B-Series
Replacement
- Raise and support vehicle and remove wheel.
- Remove brake line and plug to avoid fluid loss and air entering line.
- Remove caliper mounting bolts.
- Reverse procedure to install.
Service
- Remove excess dirt from caliper assembly, then remove and discard dust boot.
- Place a piece of wood in caliper and gently blow compressed air into brake line hole to help force out piston. Do not pry piston out, as you may damage assembly.
- Inspect piston for wear and corrosion. Replace as needed.
- Remove piston seal and discard.
- Remove and inspect bleeder screw. Replace as needed.
- Inspec...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda B4000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda B4000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda B4000 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> B-Series -> Except B-Series & Tribute -> Manual -> Pressure -> Tribute
Vehicle: 1997 Mazda B4000 4.0 V6 GAS
Except B-Series & Tribute
- Raise and support vehicle with jack stands.
- Fill reservoir with brake fluid, ensure reservoir is at least half full at all times during bleeding procedure.
- After removing bleeder cap, connect one end of transparent vinyl tube to bleeder and place other end in a clean, clear container that is half full with brake fluid.
- One person should depress pedal a few times, then hold the pedal depressed.
- A second person should loosen the bleeder screw and drain fluid, then retighten screw to specifications.
- Repeat steps 4 and 5 until there are no more air bubbles see...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda B4000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda B4000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda B4000 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> B-Series -> Except B-Series -> Master Cylinder Overhaul -> Wheel Cylinder Overhaul
Vehicle: 1997 Mazda B4000 4.0 V6 GAS
Master Cylinder Overhaul
Except B-Series
- Remove brake fluid from reservoir after removal of master cylinder.
- Refer to Figs. through , for master cylinder disassembly.
- Visually inspect all components and repair or replace any faulty components.
- Reverse procedure to assemble.
B-Series
- Clean outside of master cylinder and drain fluid after removal.
- Remove snap ring by depressing rear piston, Fig. .
- Remove primary piston from master cylinder, then remove secondary piston by directing compressed air ...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda B4000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda B4000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda B4000 cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 1997 Mazda B4000 4.0 V6 GAS
When the brake pedal is depressed, a vacuum builds up in the booster which amplifies the pedal force, pressing on the piston in the master cylinder. The piston raises the hydraulic pressure in the cylinder. This hydraulic pres...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda B4000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda B4000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda B4000 cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> 1997-98 -> 2000-01 -> 2WD -> 4WABS -> 4WD -> ABS Control Module -> ABS Relay -> B-Series -> Brake System Bleed -> Component Replacement -> Computer Module -> Front Wheel Speed Sensor -> Front Wheel Speed Sensor Rotor -> Hydraulic Unit -> Miata -> Millenia -> Millenia & Protege -> MPV -> MX-6 & 626 -> Rear -> Rear Anti-Lock Brake System (RABS) Sensor -> Rear Anti-Lock Brake System (RABS) Valve -> Rear Wheel Speed Sensor -> Rear Wheel Speed Sensor Rotor -> Tribute
Vehicle: 1997 Mazda B4000 4.0 V6 GAS
Brake System Bleed
Refer to "Hydraulic Brake System" for bleed procedure.
Component Replacement
ABS Relay
Millenia & Protege
- Remove cruise control actuator assembly, then disconnect relay electrical connector.
- Remove relay mounting nut, then the relay.
- Reverse procedure to install. Torque relay mounting nut to 70-95 inch lbs. and cruise control actuator mounting nuts to 26-34 inch lbs.
Hydraulic Unit
B-Series
4WABS
- Raise and support vehicle, then remove left front wheel and fender apron.
- Remove hydraulic unit nut, then lower vehicle and remove unit.
- Reverse procedure to install, noting the foll...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda B4000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1997 Mazda B4000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1997 Mazda B4000 cars and light trucks from 1990+.
Anti-lock Brakes -> Description
Vehicle: 1997 Mazda B4000 4.0 V6 GAS
The anti-lock brake system (ABS) is composed of electrical and mechanical components as well as the standard braking system comp...
CLICK HERE TO GET FULL ACCESS TO 1997 Mazda B4000 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1997 Mazda B4000 vehicle. |
Access the Complete guide! |