Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1998 Chevrolet Blazer car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1998 Chevrolet Blazer automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Blazer cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> Troubleshooting -> Brakes Grab -> Hard Pedal -> Slow Or No Release
Vehicle: 1998 Chevrolet Blazer 4.3 V6 GAS
Hard Pedal
- Internal vacuum leak.
- Faulty control valve.
- Broken or damaged hydraulic brake lines.
- Collapsed or damaged vacuum hose.
- Plugged or loose vacuum fitting.
- Bad stud welds on front or rear housing on power head.
- Faulty booster diaphragm.
- Restricted air filter element.
- Worn or distorted reaction plate or levers.
- Cracked or broken pow...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Blazer cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> General Service
Vehicle: 1998 Chevrolet Blazer 4.3 V6 GAS
Certain general service procedures apply, regardless of whether the brakes are vacuum or hydraulically assisted. Only top quality, clean brake fluid should be used. More seals and valves are used with power brake systems than with ordinary brakes, so an inferior brake fluid will do much more damage. For the same reason, ensure all dirt is kept out of the system. Additionally, on models with hydraulic assist brakes, care must be taken not to mix the fluids of the booster hydraulic system and brake hydraulic system as the fluids are not compatible.
If the power unit fails, the brak...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Blazer cars and light trucks from 1990+.
Drum Brakes -> Adjustments -> Astro, Bravada, S & T Series & Safari -> Automatic Apply Parking Brakes -> Aztek, Montana, Silhouette, Trans Sport & Venture -> C & K Series -> Control Rod -> G & P Series -> Lever Type -> Manual Parking Brake -> Optional Method -> Pedal Type -> Propeller Shaft Type -> Service Brake -> Standard Method -> Tracker
Vehicle: 1998 Chevrolet Blazer 4.3 V6 GAS
Service Brake
These brakes have self-adjusting shoe mechanisms that ensure correct lining-to-drum clearances at all times. The automatic adjusters operate only when the brakes are applied as the vehicle is moving rearward or when the car comes to an uphill stop.
Although the brakes are self-adjusting, an initial adjustment is necessary after the brake shoes have been relined or replaced, or when the length of the adjusting screw has been changed during some other service operation.
Frequent usage of an automatic transmission forward range to halt reverse vehicle motion may prevent the ...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Blazer cars and light trucks from 1990+.
Anti-lock Brakes -> Kelsey-Hayes -> System Service -> 1997-2000 C & K Series Except 1999-2000 Sierra, Silverado & 2000 Suburban, Tahoe & Yukon -> 1997-2000 w/310 ABS -> 1999-2000 Sierra, Silverado & 2000 Suburban, Tahoe, Yukon & 2001 C & K Series -> 2000-01 w/325 ABS -> Astro & Safari -> Brake Pressure Modulator Valve (BPMV) -> Brake System Bleed -> C & K Series Except C3500HD -> C3500HD -> Component Replacement -> Electronic Brake Control Module (EBCM) -> Front Wheel Speed Sensor -> G Van -> Installation -> Manual Bleed -> P Series -> Pressure Bleed -> Removal -> S & T Series
Vehicle: 1998 Chevrolet Blazer 4.3 V6 GAS
Brake System Bleed
Gravity and vacuum bleeding procedures are not recommended for use with the anti-lock brake system. The manual bleed procedure is the preferred method, although pressure bleeding is also possible. Do not pump the brake pedal during the bleeding process, as fluid aeration may occur.
Manual Bleed
- Raise and support vehicle, then connect a clear plastic tube to brake bleed screw at righthand rear wheel.
- Place free end of tube in a glass jar partially filled with clean brake fluid. Ensure end of tube remains submerged in fluid and master cylinder reservoir is kept full.
- ...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Blazer cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> Power Brake Unit Service
Vehicle: 1998 Chevrolet Blazer 4.3 V6 GAS
The power brake unit is n...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Blazer cars and light trucks from 1990+.
Power Brake Units -> Bendix Brake Booster -> Power Brake Unit Service -> Accumulator Service -> Assemble -> Booster Bleed -> Cleaning & Inspection -> Disassemble
Vehicle: 1998 Chevrolet Blazer 4.3 V6 GAS
Disassemble
- Place accumulator compressor tool No. J-26889, or equivalent, around end of accumulator.
- Install nut onto stud as shown in Fig. , then depress the accumulator with a C-clamp.
- Remove retainer by using a punch.
- Release C-clamp and remove accumulator compressor tool.
- Remove accumulator, O-ring, retainer, plug and spring, Fig. .
- Remove retainer, output pushrod, baffle, piston return spring and retainer.
- Using a suitable saw, cut off eyelet of pedal rod, then remove the boot.
- Remove nut, bracket and bolts, then separate cover from housing.
- Remove piston assembly and seal...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Blazer BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
