Auto Parts Search
1998 Ford E-350 Econoline CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1998 Ford E-350 Econoline AUTOMOBILES
Component Replacement & Adjustment -> Light Duty Trucks & Vans -> Electric Actuators, Replace -> Econoline -> Expedition & Navigator -> Explorer & Mountaineer -> F-Series -> Panel/Floor/Defrost -> Ranger -> Recirculate/Fresh -> Temperature Blend -> Temperature Blend/Panel Bypass -> Villager -> Windstar
Vehicle: 1998 Ford E-350 Econoline 7.3 V8 DIESEL
Econoline
- Remove instrument panel finish panel.
- Disconnect electronic door actuator motor connector.
- Remove actuator mounting screws, then the A/C electronic door actuator motor, Fig. .
- Reverse procedure to install.
Expedition & Navigator
- Remove floor duct panel.
- Remove right side instrument panel brace.
- Remove left side instrument panel lower nut and position brace aside.
- Remove floor duct, then the electronic actuator.
- Reverse procedure to install.
Explorer & Mountaineer
- Remove instr...
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Ford E-350 Econoline AUTOMOBILES
Power Brake Units -> Bendix Vacuum Brake Booster -> Adjustments -> 1997 Windstar -> Aerostar, F-Series & Ranger -> Expedition, Explorer, F-150 & F-250LD, Mountaineer, Navigator & Villager -> Pushrod -> Villager
Vehicle: 1998 Ford E-350 Econoline HD Club Wagon 7.3 V8 DIESEL
Pushrod
Aerostar, F-Series & Ranger
To measure pushrod adjustment, use a suitable gauge and position it against the master cylinder mounting surface as illustrated in Fig. . Adjust pushrod screw by turning it until the end just touches inner edge of gauge slot.
Expedition, Explorer, F-150 & F-250LD, Mountaineer, Navigator & Villager
Refer to "Brake Booster, Replace" for pushrod adjustment.
Villager
Refer to "Brake Booste... "
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1998 Ford E-350 Econoline AUTOMOBILES
Ford Motor Co. Light Trucks, SUVs & Vans -> Fuel Filter Replacement -> Except Diesel Engines & Villager
Vehicle: 1998 Ford E-350 Econoline Super Wagon 6.8 V10 GAS
The fuel system remains under high pressure even when the engine is not running. This residual pressure must be relieved before servicing the fuel system. To avoid injury or fire, release pressure from the fuel system before disconnecting any fuel line.
The fuel system pressure must be relieved prior to disconnecting fuel lines to prevent accidental spray of fuel.
After the battery has been disconnected and reconnected, some abnormal driveability symptoms may occur. The vehicle may need to be driven 10 miles or more while it relearns its adaptive strategy.
On model...
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Ford E-350 Econoline AUTOMOBILES
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 1998 Ford E-350 Econoline Super 6.8 V10 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1998 Ford E-350 Econoline AUTOMOBILES
Alternator, Replace
Vehicle: 1998 Ford E-350 Econoline Super 5.4 V8 GAS
- Disconnect battery ground cable.
- Disconnect electrical connector from alternator.
- Remove alternator drive belt.
- Remove alternator...
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1998 Ford E-350 Econoline AUTOMOBILES
Ford Motor Co. Trucks -> Check Fuel Cap Lamp ->
Vehicle: 1998 Ford E-350 Econoline 5.4 V8 GAS
The Check Fuel Cap Lamp will illuminate momentarily when the ignition switch is placed in the On position as a bulb check. If the lamp remains...
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1998 Ford E-350 Econoline AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 1998 Ford E-350 Econoline 5.4 V8 GAS
Lower
- Drain cooling system into a suitable container.
- Reposition hose clamp from radiator.
- Remove radiator outlet hose from radiator.
- Reposition hose clamp from water inlet.
- Remove radiator outlet hose from water inlet and from vehicle.
- Reverse procedur...
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1998 Ford E-350 Econoline AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1998 Ford E-350 Econoline 7.3 V8 DIESEL
- Loosen accessory adjustment bolt and pivot bolt.
- Remove belt.
- Reverse procedure to install, adjust belt tension as follows:
- Loosen adjustment bolts then install a suitable belt tension gauge.
- Tighten pivot bolt enough to remove freeplay from pivot area.
- To adjust all belts except alternator, install square drive ratchet wrench or breaker bar to square hole in accessory bracket and tighte...
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1998 Ford E-350 Econoline AUTOMOBILES
Component location diagrams for most 1998 Ford E-350 Econoline cars and light trucks sold in the U.S. from 1990+.
Engine Components & Connectors Diagram for 1998 Ford E-350 Econoline Super 5.4 V8 BI-FUEL Components on diagram: |
I/P Components & Connectors Diagram for 1998 Ford E-350 Econoline 5.4 V8 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1998 Ford E-350 Econoline AUTOMOBILES
OEM drawn wiring diagrams for most 1998 Ford E-350 Econoline cars and light trucks sold in the U.S.
1998 Ford E-350 Econoline Super 6.8 V10 GAS Wiring Diagram Components on diagram: |
1998 Ford E-350 Econoline 5.4 V8 BI-FUEL Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1998 Ford E-350 Econoline AUTOMOBILES
OEM TSB listings for most 1998 Ford E-350 Econoline cars and light trucks sold in the U.S. from 1985+.
Document: RECALL - CERTAIN 1992-2003 MODEL YEAR CARS AND TRUCKS - FUSED JUMPER HARNESS REPLACEMENT FOR VEHICLES SERVICED WITH AN INCOMPATIBLE FUSED JUMPER HARNESS Vehicle: 1998 Ford E-350 Econoline 5.4 V8 GAS Auto Systems: |
Document: RECALL - FUSED JUMPER HARNESS REPLACEMENT FOR VEHICLES SERVICED WITH AN INCOMPATIBLE FUSED JUMPER HARNESS Vehicle: 1998 Ford E-350 Econoline 5.4 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1998 Ford E-350 Econoline AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1998 Ford E-350 Econoline cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1998 Ford E-350 Econoline cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1998 Ford E-350 Econoline cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1998 Ford E-350 Econoline cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1998 Ford E-350 Econoline SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1998 Ford E-350 Econoline vehicle. |
Access the Complete guide! |