Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1999 Mercury Sable car and truck
repair procedures including Mercury engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1999 Mercury Sable automobile. Try the Automotix DIY solution today!
We have info for following modifications of 1999 Mercury Sable
- 1999 Mercury Sable 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:U
- 1999 Mercury Sable 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:S
BRAKE SERVICE PROCEDURES FOR 1999 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Mercury Sable cars and light trucks from 1990+.
Drum Brakes -> Contour, Cougar, Mystique, Sable & Taurus -> Adjustments -> Parking Brake -> Service Brakes
Vehicle: 1999 Mercury Sable 3.0 V6 GAS
Service Brakes
Although the brakes are self-adjusting, an initial adjustment will be required after a brake repair. This adjustment is performed as follows:
- Determine inside diameter of brake drum surface using brake shoe gauge tool No. D81L-1103-A, or equivalent. Adjust brake shoe diameter to fit gauge. Hold automatic adjusting lever out of engagement while rotating adjustin...
CLICK HERE TO GET FULL ACCESS TO 1999 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Mercury Sable cars and light trucks from 1990+.
Disc Brakes -> Rear Disc & Parking Brakes -> Caliper Service -> Assemble -> Cleaning & Inspection -> Continental, Cougar, Mustang, Sable & Taurus -> Contour & Mystique -> Crown Victoria, Grand Marquis, Marauder & Town Car -> Disassemble -> Escort, Tracer & ZX2 -> Inspection -> Installation -> LS & Thunderbird -> Overhaul -> Removal -> Replacement
Vehicle: 1999 Mercury Sable 3.0 V6 GAS
Replacement
Continental, Cougar, Mustang, Sable & Taurus
Removal
- Raise and support rear of vehicle, then remove wheel and tire assembly.
- Disconnect brake hose from caliper assembly.
- Remove retaining clip, then disconnect parking brake cable from lever arm.
- Remove pinch bolts using open end wrench to hold slider pin in position, Fig. .
- Lift caliper assembly from anchor plate, then remove slider pins and boots.
Installation
- Apply suitable silicone dielectric compound to slider pins and inside of boots.
- Place slider pins and boots on anchor plate, then position caliper assembly on anchor pla...
CLICK HERE TO GET FULL ACCESS TO 1999 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Mercury Sable cars and light trucks from 1990+.
Hydraulic Brake Systems -> Hydraulic Brake System Flush
Vehicle: 1999 Mercury Sable 3.0 V6 GAS
Whenever new brake components are installed in the hydraulic system, it is recommended that the entire hydraulic system be thoroughly flushed with clean brake fluid.
It may sometime become required to flush out the system due to the presence of mineral oil, kerosene, gasoline, etc., which will cause swelling of rubber piston cups and valves and render them inoperative.
Flushing is performed at e...
CLICK HERE TO GET FULL ACCESS TO 1999 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Mercury Sable cars and light trucks from 1990+.
Disc Brakes -> Rear Disc & Parking Brakes -> Troubleshooting -> Brake Roughness
Vehicle: 1999 Mercury Sable 3.0 V6 GAS
Brake Roughness
If roughness or vibration is encountered during highway operation or if pedal pumping is experienced at low speeds, the disc may have excessive thickness variation. Measure the disc at 12 points with a micrometer at a radius approximately one inch from the edge of the disc. If thickness measurements vary by more than .0005 inch, replace the rotor.
Excessive later...
CLICK HERE TO GET FULL ACCESS TO 1999 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Mercury Sable cars and light trucks from 1990+.
Power Brake Units -> Precautions -> Battery Ground Cable
Vehicle: 1999 Mercury Sable 3.0 V6 GAS
Battery Ground Cable
Prior to service, dis...
CLICK HERE TO GET FULL ACCESS TO 1999 Mercury Sable BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Mercury Sable AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Mercury Sable cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Disassemble -> Inspection -> Master Cylinder Overhaul -> Overhaul -> Wheel Cylinders
Vehicle: 1999 Mercury Sable 3.0 V6 GAS
Master Cylinder Overhaul
Disassemble
- Clean outside of master cylinder thoroughly. Drain brake fluid from master cylinder.
- Remove stop bolt and pressure control valves, if equipped.
- Pry up on reservoir and remove it from master cylinder body.
- Remove fluid control valve, if equipped.
- Depress primary piston and remove snap ring from retaining groove at open end of bore.
- Remove primary and secondary piston assemblies from master cylinder. If secondary piston does not come out, apply air pressure to secondary outlet port to remove.
Inspection
When disassembled, wash all parts in clean brake...
CLICK HERE TO GET FULL ACCESS TO 1999 Mercury Sable BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1999 Mercury Sable vehicle.
|
| Access the Complete guide! |
