Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2000 Mitsubishi Montero car and truck
repair procedures including Mitsubishi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2000 Mitsubishi Montero automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2000 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mitsubishi Montero cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> 2001-02 Montero -> 3000GT -> AWD Models -> Brake Fluid Pressure Switch -> Brake System Bleed -> Component Replacement -> Diamante -> Eclipse -> Electronic Control Unit & Power Relay -> Front Speed Sensor -> G-Sensor -> Galant -> Hydraulic Brake Booster -> Hydraulic Unit -> Lancer -> Mirage -> Montero Sport & 1997-2000 Montero -> Montero, Montero Sport & 3000GT -> Rear Speed Sensor
Vehicle: 2000 Mitsubishi Montero 3.5 V6 GAS
Brake System Bleed
- Bleed brake master cylinder as follows:
- Fill master cylinder reservoir with DOT 3 or DOT 4 brake fluid, then depress brake pedal fully and plug master cylinder outlet fitting.
- With fitting opening plugged, release brake pedal. Perform this operation several times to fill master cylinder with brake fluid and purge all air.
- Start engine and bleed air from hydraulic lines. Refer to Figs. and , for hydraulic line bleed sequence. Ensure master cylinder reservoir is kept full during bleed procedure.
- Ensure brake pedal feels firm when applied. Inspect and fill master cyl...
CLICK HERE TO GET FULL ACCESS TO 2000 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mitsubishi Montero cars and light trucks from 1990+.
Drum Brakes -> Brake Service
Vehicle: 2000 Mitsubishi Montero 3.5 V6 GAS
For drum brake service ...
CLICK HERE TO GET FULL ACCESS TO 2000 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mitsubishi Montero cars and light trucks from 1990+.
Disc Brakes -> Montero & Montero Sport -> Brake System Bleed
Vehicle: 2000 Mitsubishi Montero 3.5 V6 GAS
The hydraulic brake system must be bled if air has entered the system. Air may enter due to low fluid level, a hydraulic fluid leak, opening of a hydraulic line or replacement of a hydraulic system component. Symptoms include loss of brake operation and/or a low or spongy brake pedal.
On models with ABS, use a suitable filter when adding fluid to reservoir tank.
- Ensure master cylinder reservoir is full. Add suitable brake fluid as needed, and securely reinstall the master cylinder cap.
- Raise and support vehicle.
- Position a drain pan under the wheel being bled.
- Have an assistant de...
CLICK HERE TO GET FULL ACCESS TO 2000 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mitsubishi Montero cars and light trucks from 1990+.
Disc Brakes -> Montero & Montero Sport -> Rotor Replacement -> 2WD Models -> 4WD Models
Vehicle: 2000 Mitsubishi Montero 3.5 V6 GAS
2WD Models
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove front brake assembly and suspend assembly with wire.
- Remove hub cap, then the cotter pin.
- Remove slotted nut and washer, then the outer bearing.
- Remove front hub and rotor assembly.
- Reverse procedure to install, noting the following:
- Tighten slotted wheel bearing nut to specifications.
- Loosen slotted nut completely.
- Torque slotted nut to 72 inch lbs.
4WD Models
- Place free wheeling hub in "Free" position.
- Rotate hub cover counterclockwise and remove.
- Remove snap ring from end of driveshaft.
- Remove adjusting shims (if ...
CLICK HERE TO GET FULL ACCESS TO 2000 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mitsubishi Montero cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting -> General Fault Diagnosis -> Transient Fault Diagnosis
Vehicle: 2000 Mitsubishi Montero 3.5 V6 GAS
General Fault Diagnosis
Problems related to Anti-Lock Brake System (ABS) can generally be classified as electrical or hydraulic.
For problems in electrical system, a self-diagnostic function is built into Electronic Control Unit (ECU), allowing ABS warning lamp to illuminate as a warning to driver in event of an abnormality. In this instance, inspections can be performed with a voltmeter, Multi-Use Tester (MUT), oscilloscope or ABS warning lamp.
Problems with hydraulic system can be located in same manner as ordinary brakes. It is, however, required to determine whether problem is ...
CLICK HERE TO GET FULL ACCESS TO 2000 Mitsubishi Montero BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2000 Mitsubishi Montero AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2000 Mitsubishi Montero cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Cleaning & Inspection -> Disassemble -> Master Cylinder -> Overhaul -> Service -> Wheel Cylinder
Vehicle: 2000 Mitsubishi Montero 3.5 V6 GAS
Master Cylinder
Service
- Disassemble master cylinder as outlined in numbered sequence, Figs. through . Note the position of all components as they are removed for proper installation.
- On models equipped with attached reservoir master cylinder, remove reservoir screw and cap, brake fluid sensor, float, then the reservoir, Figs. and .
- On models equipped with separately mounted reservoir, remove nipple, Fig. .
- On models equipped with separately mounted reservoir, use a wooden stick or dowel to depress primary piston into cylinder bore.
- On all models, with pushrod depressed, remove pis...
CLICK HERE TO GET FULL ACCESS TO 2000 Mitsubishi Montero BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
