Auto Parts Search
We have info for following modifications of 2000 Toyota Tundra
- 2000 Toyota Tundra 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285
- 2000 Toyota Tundra 3.4 V6 GAS, CC:3378, Fuel Injection
MAINTENANCE LAMP RESET PROCEDURES FOR 2000 Toyota Tundra AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2000 Toyota Tundra cars and light trucks sold in the U.S. from 1990+.
Toyota -> Anti-Lock Brake System (ABS)/Vehicle Stability Control (VSC) System Warning Lamp -> 2000-09 Tundra
Vehicle: 2000 Toyota Tundra 3.4 V6 GAS
The anti-lock warning lamp is used to warn of a system fault. The lamp will be lit during engine start-up, but should go out when the self-diagnostic system verifies proper anti-lock operation. If the lamp remains lit, a fault in the anti-lock brake system is indicated. After system diagnosis and repair are complete, the lamp can be reset using the following procedures:
- Place ignition switch ...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tundra MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2000 Toyota Tundra AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2000 Toyota Tundra cars and light trucks sold in the U.S. from 1990+.
Toyota -> Automatic Transmission Oil Temperature Warning Lamp ->
Vehicle: 2000 Toyota Tundra 4.7 V8 GAS
This lamp will be illuminated when automatic transmission or transfer case fluid temperature exceeds 302°F. If the lamp lights, allow vehicle to operate at idle speed until fluid temperature falls below 248°F; t...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tundra MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2000 Toyota Tundra AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2000 Toyota Tundra cars and light trucks sold in the U.S. from 1990+.
Toyota -> Automatic Transmission Overdrive Lamp ->
Vehicle: 2000 Toyota Tundra 4.7 V8 GAS
The "OD Off" lamp will be illuminated when the ignition switch is in the On position and the Overdrive (OD) switch is in the Off position. When the OD switch is placed in the On position, the "OD Off" lamp should go out. If the lamp flashes when the switch is placed in the On position, a fault has been detected by the electronic control system. After diagnosis and repair are c...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tundra MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2000 Toyota Tundra AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2000 Toyota Tundra cars and light trucks sold in the U.S. from 1990+.
Toyota -> Air Bag Warning Lamp -> 2000-04 Tundra
Vehicle: 2000 Toyota Tundra 3.4 V6 GAS
- Connect service wires to check connector terminals Tc and AB.
- Place ignition switch in Accessory or On positions and wait approximately 6 seconds.
- Apply body ground to terminals Tc and AB alternately, twice in 1 second intervals beg...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tundra MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2000 Toyota Tundra AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2000 Toyota Tundra cars and light trucks sold in the U.S. from 1990+.
Toyota -> Automatic Transmission Oil Temperature Warning Lamp ->
Vehicle: 2000 Toyota Tundra 3.4 V6 GAS
This lamp will be illuminated when automatic transmission or transfer case fluid temperature exceeds 302°F. If the lamp lights, allow vehicle to operate at idle speed until fluid temperature falls below 248°F; t...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tundra MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2000 Toyota Tundra AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2000 Toyota Tundra cars and light trucks sold in the U.S. from 1990+.
Toyota -> Automatic Transmission Overdrive Lamp ->
Vehicle: 2000 Toyota Tundra 3.4 V6 GAS
The "OD Off" lamp will be illuminated when the ignition switch is in the On position and the Overdrive (OD) switch is in the Off position. When the OD switch is placed in the On position, the "OD Off" lamp should go out. If the lamp flashes when the switch is placed in the On position, a fault has been detected by the electronic control system. After diagnosis and repair are c...
CLICK HERE TO GET FULL ACCESS TO 2000 Toyota Tundra MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2000 Toyota Tundra vehicle. |
Access the Complete guide! |