Auto Parts Search
2001 Ford E-250 Econoline CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service

A/C & HEATER SERVICE PROCEDURES FOR 2001 Ford E-250 Econoline AUTOMOBILES
Component Replacement & Adjustment -> Light Duty Trucks & Vans -> Actuator & Control Motors, Replace -> 2001 -> 2002 -> Air Inlet Vacuum Motor -> Air Inlet Vacuum Motor -> Auxiliary Diverter Electronic Actuator -> Auxiliary Temperature & Air Distribution Blend Doors -> Auxiliary Temperature Blend Electronic Actuator -> Blackwood, Expedition & Navigator -> Defroster Airflow Vacuum Motor -> Econoline -> Escape -> Excursion & F-Super Duty -> Explorer & Mountaineer -> Explorer Sport & Sport Trac -> F-150 -> Floor Airflow Vacuum Motor -> Front Temperature Blend Electronic Actuator -> Lefthand Temperature Blend Electronic Actuator -> Panel Airflow Vacuum Motor -> Panel/Defrost Vacuum Motor -> Panel/Floor & Air Inlet Vacuum Motors -> Panel/Floor Vacuum Motor -> Ranger -> Recirculation Air Duct Vacuum Motor -> Righthand Dual Automatic Temperature Control (DATC) Temperature Blend -> Temperature Blend Electronic Actuator -> Vacuum Motors -> Windstar
Vehicle: 2001 Ford E-250 Econoline 5.4 V8 GAS
Do not bend the actuator lever.
Blackwood, Expedition & Navigator
Front Temperature Blend Electronic Actuator
- On models equipped with center console, remove center console blower motor as outlined under "Blower Motor,"
- On all models, remove pin-type retainers and expand clip.
- Remove front seats.
- Remove kick panel and sill trim.
- Pull back carpet and remove floor duct panel.
- Disconnect electrical connector and remove blend door actuator mounting screws.
- Disconnect actuator shaft by pulling it down, then re...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Ford E-250 Econoline AUTOMOBILES
Hydraulic Brake Systems -> Diagnosis & Testing
Vehicle: 2001 Ford E-250 Econoline 5.4 V8 CNG
Refer to "Diagnosis & Testin... "
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2001 Ford E-250 Econoline AUTOMOBILES
Ford Motor Co. Light Trucks, SUVs & Vans -> Fuel Filter Scheduled Maintenance -> 1993-06 Econoline w/Gasoline Engine -> Normal Service -> Severe Service
Vehicle: 2001 Ford E-250 Econoline 5.4 V8 GAS
Normal Service
Replace ...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Ford E-250 Econoline AUTOMOBILES
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2001 Ford E-250 Econoline 4.2 V6 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2001 Ford E-250 Econoline AUTOMOBILES
Starter, Replace
Vehicle: 2001 Ford E-250 Econoline 5.4 V8 CNG
- Disconnect battery ground cable.
- Raise and support vehicle.
- When disconnecting hardshell connector at starter motor solenoid S-terminal, grasp plastic shell and pull off. Do not pull on wires.
- Pull straight off to prevent damage to connector and S-terminal.
- Replace damaged components, if required.
- Remove starter moto...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2001 Ford E-250 Econoline AUTOMOBILES
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 2001 Ford E-250 Econoline 5.4 V8 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2001 Ford E-250 Econoline AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2001 Ford E-250 Econoline 4.2 V6 GAS
Inlet
- Drain cooling system into a suitable container.
- Reposition heater core inlet hose clamp at engine.
- Remove hose from engine.
- Reposition heater hose inlet clamp at heater core.
- Remove heater inlet hose from heater core.
- Remove hose from vehicle.
- Reverse procedure to in...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2001 Ford E-250 Econoline AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2001 Ford E-250 Econoline 5.4 V8 CNG
- Rotate drive belt tensioner counterclockwise, using a 1/2 square hole in drive belt tensioner pull...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2001 Ford E-250 Econoline AUTOMOBILES
Component location diagrams for most 2001 Ford E-250 Econoline cars and light trucks sold in the U.S. from 1990+.
![]() Components on diagram: |
![]() Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2001 Ford E-250 Econoline AUTOMOBILES
OEM drawn wiring diagrams for most 2001 Ford E-250 Econoline cars and light trucks sold in the U.S.
![]() Components on diagram: |
![]() Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2001 Ford E-250 Econoline AUTOMOBILES
OEM TSB listings for most 2001 Ford E-250 Econoline cars and light trucks sold in the U.S. from 1985+.
Document: SAFETY RECALL - SPEED CONTROL SYSTEM MODIFICATION Vehicle: 2001 Ford E-250 Econoline 4.2 V6 GAS Auto Systems: |
Document: RECALL - CERTAIN 1992-2003 MODEL YEAR CARS AND TRUCKS - FUSED JUMPER HARNESS REPLACEMENT FOR VEHICLES SERVICED WITH AN INCOMPATIBLE FUSED JUMPER HARNESS Vehicle: 2001 Ford E-250 Econoline 4.2 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2001 Ford E-250 Econoline AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2001 Ford E-250 Econoline cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2001 Ford E-250 Econoline cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2001 Ford E-250 Econoline cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2001 Ford E-250 Econoline cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2001 Ford E-250 Econoline SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
![]() |
Access the Complete guide! |