Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2001 Ford Explorer car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2001 Ford Explorer automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2001 Ford Explorer
- 2001 Ford Explorer 5.0 V8 GAS, CID:302, Fuel Injection, Aspiration:302, Engine VIN:, Desg:P
- 2001 Ford Explorer 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
- 2001 Ford Explorer Sport 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
MAINTENANCE LAMP RESET PROCEDURES FOR 2001 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2001 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Engine Lamp -> 1998-2006 EEC-V -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool
Vehicle: 2001 Ford Explorer 4.0 V6 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-V system. If the lamp remains On or starts to blink, a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
A temporary fault such as running out of fuel, poor quality or water in fuel or loose...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2001 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2001 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Rear Load Leveling (CHECK SUSP) ->
Vehicle: 2001 Ford Explorer Sport 4.0 V6 GAS
The CHECK SUSP indicator lights when there is a fault of the rear load ...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2001 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2001 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Engine Lamp -> 1998-2006 EEC-V -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool
Vehicle: 2001 Ford Explorer Sport 4.0 V6 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-V system. If the lamp remains On or starts to blink, a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
A temporary fault such as running out of fuel, poor quality or water in fuel or loose...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2001 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2001 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Anti-Lock Or Rear Anti-Lock Brake System Warning ->
Vehicle: 2001 Ford Explorer 5.0 V8 GAS
Red and yellow indicator lamps are used to warn of system faults. The red lamp warns of such faults as low brake fluid level, parking brake On, system pressure differential and other system faults. The red indicator lamp will light for approximately two seconds during engine starting and should go off, unless parking brake is applied or a problem in the brake system exist. The red indicator lamp should reset after repairs to system have ...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2001 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2001 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Low Oil Level Warning Indicator ->
Vehicle: 2001 Ford Explorer 4.0 V6 GAS
This system is used to indicate a low engine oil level condition. The lamp should light during engine starting. If oil level is sufficient, the lamp should go off when engine is operating. If oil level is low the...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2001 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2001 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 2001 Ford Explorer 4.0 V6 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 2001 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
