Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2001 Toyota Sienna car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2001 Toyota Sienna automobile. Try the Automotix DIY solution today!
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Toyota Sienna AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 Toyota Sienna cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2001 Toyota Sienna 3.0 V6 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Drain transmission fluid and transfer case oil.
- Unstake drive shaft hub nut.
- With an assistant applying brakes, remove drive shaft hub nut.
- Remove nut, then disconnect stabilizer bar link fro shock absorber.
- Remove bolt and separate ABS speed sensor wire and hose from shock absorber.
- Remove bolt, then remove ABS speed sensor from steering knuckle.
- Remove cotter pin and nut, then separate tie rod end from steering knuckle, using a suitable pry tool.
- Remove bolt and nuts from lower ball joint, then separate lower control arm...
CLICK HERE TO GET FULL ACCESS TO 2001 Toyota Sienna DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Toyota Sienna AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 Toyota Sienna cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2001 Toyota Sienna 3.0 V6 GAS
- Raise and support vehicle.
- Remove exhaust pipe.
- Have an assistant depress and hold brake pedal.
- Loosen the cross groove joint set bolts a 1/2 turn.
- Place reference marks on both flanges.
- Remove nuts, bolts and washers at flanges.
- Remove bolts and adjusting shims from...
CLICK HERE TO GET FULL ACCESS TO 2001 Toyota Sienna DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2001 Toyota Sienna AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2001 Toyota Sienna cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2001 Toyota Sienna 3.0 V6 GAS
Disassemble
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance. Do not tighten driveshaft too tightly in a vise because this will cause driveline to become out of balance and result in driveline vibration.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap ri...
CLICK HERE TO GET FULL ACCESS TO 2001 Toyota Sienna DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
