Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2002 Chevrolet Blazer car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2002 Chevrolet Blazer automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2002 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Chevrolet Blazer cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Brake Pad Service
Vehicle: 2002 Chevrolet Blazer 4.3 V6 GAS
The procedures to remove and install the brake pads are outlined in. "Calip... "
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Chevrolet Blazer cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Rotor Replacement -> 2WD Models -> 4WD Models -> Except K3500 -> Except Montana, Silhouette, Trans Sport & Venture -> Front -> K3500 -> Montana, Silhouette, Trans Sport & Venture -> Rear
Vehicle: 2002 Chevrolet Blazer 4.3 V6 GAS
2WD Models
Except Montana, Silhouette, Trans Sport & Venture
Front
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove caliper as outlined in. "Caliper Service."
- Remove grease cap from hub/rotor,. Fig. .
- Remove cotter pin, nut and washer.
- Remove hub/rotor from spindle, being careful not to damage spindle threads or outer bearing.
- Reverse procedure to install, noting the following:
- Apply high-temperature wheel bearing grease to inner and outer wheel bearings.
- Torque nut to 12 ft. lbs., while turning wheel assembly forward by hand, back nut off one flat or until hole in spindle...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Chevrolet Blazer cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Description
Vehicle: 2002 Chevrolet Blazer 4.3 V6 GAS
The caliper mounts in a way that allows the caliper to move laterally inboard as the brake pads wear. The caliper housing is a one piece casting with the inboard side containing the piston bore. The piston seal also acts as a return mechanism for the piston.
Applying the brake pedal causes the hydraulic pressure that moves the caliper piston. The piston then forces the inboard brake pad against the inboard braking surface of the rotor. Increasing the force against...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Chevrolet Blazer cars and light trucks from 1990+.
Power Brake Units -> Delco Brake Booster -> General Service
Vehicle: 2002 Chevrolet Blazer 4.3 V6 GAS
Certain general service procedures apply, regardless of whether the brakes are vacuum or hydraulically assisted. Only top quality, clean brake fluid should be used. More seals and valves are used with power brake systems than with ordinary brakes, so an inferior brake fluid will do much more damage. For the same reason, ensure all dirt is kept out of the system. Additionally, on models with hydraulic assist brakes, care must be taken not to mix the fluids of the booster hydraulic system and brake hydraulic system as the fluids are not compatible.
If the power unit fails, the brak...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Chevrolet Blazer cars and light trucks from 1990+.
Anti-Lock Brakes -> Kelsey-Hayes -> Description
Vehicle: 2002 Chevrolet Blazer 4.3 V6 GAS
When wheel slip is detected during a brake application, the ABS enters anti-lock mode. During anti-lock braking, hydraulic pressure in the individual wheel circuits is controlled to prevent any wheel from slipping. A separate hydraulic line and specific solenoid valves are provided for each wheel. The ABS can decrease, hold, or increase hydraulic pressure to each wheel brake. The ABS cannot, however, increase hydraulic pressure above the amount which is transmitted by the master cylinder during braking.
During anti-lock braking, a series of rapid pulsations is felt in the brake pedal...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Blazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2002 Chevrolet Blazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2002 Chevrolet Blazer cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Bendix Master Cylinder -> Delco Master Cylinder -> Disassemble -> Tracker Master Cylinder -> Wheel Cylinder
Vehicle: 2002 Chevrolet Blazer 4.3 V6 GAS
Delco Master Cylinder
When performing the following procedures, refer to. Figs. and , noting that the composite reservoir may vary in design.
Disassemble
- Remove master cylinder from vehicle.
- Remove reservoir cover and diaphragm. Discard old brake fluid in reservoir.
- Inspect cover and diaphragm. Replace if cut, cracked or deformed.
- Remove fluid level switch and proportioning valve assembly, if equipped.
- Depress primary piston and remove lock ring.
- Plug primary fluid outlet (outlet nearest to cowl when master cylinder is installed), then apply compressed air into secondary fluid outlet...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Blazer BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
