Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2002 Chevrolet Camaro car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2002 Chevrolet Camaro automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2002 Chevrolet Camaro
- 2002 Chevrolet Camaro SS 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:G
- 2002 Chevrolet Camaro 3.8 V6 GAS, CID:231, Fuel Injection, Aspiration:231, Engine VIN:, Desg:K
- 2002 Chevrolet Camaro Z28 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:G
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2002 Chevrolet Camaro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2002 Chevrolet Camaro cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassembly
Vehicle: 2002 Chevrolet Camaro 3.8 V6 GAS
Disassembly
- Support propeller shaft in a horizontal position that is aligned with base plate of a press.
- Place universal joint so that lower ear of shaft yoke is supported on a 29mm (1.125 inch) socket.
- In order to remove lower bearing cap from yoke ear proceed as follows:
- Place U-Joint Bearing Separator J 9522 - 3 or equivalent on open horizontal bearing cap.
- Press lower bearing cap out of yoke ear. This process shears nylon injected ring on lower bearing cap.
- If bearing cap is not completely removed, use following steps in order to completely remove bearing cap:
- Lift U-Jo...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Camaro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2002 Chevrolet Camaro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2002 Chevrolet Camaro cars and light trucks from 1990+.
DRIVESHAFT, Replace -> One piece -> Two piece
Vehicle: 2002 Chevrolet Camaro SS 5.7 V8 GAS
One piece
- Raise and suitably support vehicle.
- Mark relationship of propeller shaft to pinion gear yoke.
- Remove propeller shaft bolts/screws.
- Remove propeller shaft retainers. Support propeller shaft during removal.
- Withdraw slip yoke from transmission.
- Move propeller shaft rearward and pass propeller shaft under rear axle housing. If bearing caps are loose, tape bearing caps together in order to prevent dropping and losing needle roller bearings.
- Reverse procedure to install, noting following:
- Torque propeller shaft bolt/screw to 16 ft. lbs.
- Torque propeller shaft-to-center support b...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Camaro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2002 Chevrolet Camaro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2002 Chevrolet Camaro cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassembly
Vehicle: 2002 Chevrolet Camaro SS 5.7 V8 GAS
Disassembly
- Support propeller shaft in a horizontal position that is aligned with base plate of a press.
- Place universal joint so that lower ear of shaft yoke is supported on a 29mm (1.125 inch) socket.
- In order to remove lower bearing cap from yoke ear proceed as follows:
- Place U-Joint Bearing Separator J 9522 - 3 or equivalent on open horizontal bearing cap.
- Press lower bearing cap out of yoke ear. This process shears nylon injected ring on lower bearing cap.
- If bearing cap is not completely removed, use following steps in order to completely remove bearing cap:
- Lift U-Jo...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Camaro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2002 Chevrolet Camaro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2002 Chevrolet Camaro cars and light trucks from 1990+.
DRIVESHAFT, Replace -> One piece -> Two piece
Vehicle: 2002 Chevrolet Camaro Z28 5.7 V8 GAS
One piece
- Raise and suitably support vehicle.
- Mark relationship of propeller shaft to pinion gear yoke.
- Remove propeller shaft bolts/screws.
- Remove propeller shaft retainers. Support propeller shaft during removal.
- Withdraw slip yoke from transmission.
- Move propeller shaft rearward and pass propeller shaft under rear axle housing. If bearing caps are loose, tape bearing caps together in order to prevent dropping and losing needle roller bearings.
- Reverse procedure to install, noting following:
- Torque propeller shaft bolt/screw to 16 ft. lbs.
- Torque propeller shaft-to-center support b...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Camaro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2002 Chevrolet Camaro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2002 Chevrolet Camaro cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassembly
Vehicle: 2002 Chevrolet Camaro Z28 5.7 V8 GAS
Disassembly
- Support propeller shaft in a horizontal position that is aligned with base plate of a press.
- Place universal joint so that lower ear of shaft yoke is supported on a 29mm (1.125 inch) socket.
- In order to remove lower bearing cap from yoke ear proceed as follows:
- Place U-Joint Bearing Separator J 9522 - 3 or equivalent on open horizontal bearing cap.
- Press lower bearing cap out of yoke ear. This process shears nylon injected ring on lower bearing cap.
- If bearing cap is not completely removed, use following steps in order to completely remove bearing cap:
- Lift U-Jo...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Camaro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2002 Chevrolet Camaro AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2002 Chevrolet Camaro cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2002 Chevrolet Camaro 3.8 V6 GAS
- Raise and support vehicle, then mark relationship of propeller shaft assembly to pinion gear yoke.
- Remove center support bearing and washers from torque arm assembly.
- On two-piece propeller shafts, remove bolts from center support bearing.
- On all propeller shafts, remove bolts and retainers, then propeller ...
CLICK HERE TO GET FULL ACCESS TO 2002 Chevrolet Camaro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
