Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2003 Chevrolet Corvette car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2003 Chevrolet Corvette automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2003 Chevrolet Corvette
- 2003 Chevrolet Corvette 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:G
- 2003 Chevrolet Corvette Z06 5.7 V8 GAS, CID:350, Fuel Injection, Aspiration:350, Engine VIN:, Desg:S
BRAKE SERVICE PROCEDURES FOR 2003 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Troubleshooting -> Brake Roughness
Vehicle: 2003 Chevrolet Corvette 5.7 V8 GAS
Brake Roughness
The most common cause of brake chatter on disc brakes is a variation in disc thickness. If roughness or vibration is encountered during highway operation or if pedal pulsation is experienced at low speeds, the disc may have excessive thickness variation. To inspect for this condition, measure the disc at 12 points with a micrometer at a radius approximately one inch from edge of disc. If thickness measurements vary by more than .0...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Precautions
Vehicle: 2003 Chevrolet Corvette 5.7 V8 GAS
- Grease or any other foreign material must be kept off brake linings, caliper, surfaces of disc and external surfaces of hub during service procedures.
- Handling brake disc and caliper should be done in a way to avoid deformation of disc and nicking or scratching brake linings.
- If inspection reveals worn or damaged rubber piston seals, they should be replaced.
- During removal and installation of a wheel assembly, ensure not to interfere with or dama...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Chevrolet Corvette cars and light trucks from 1990+.
Hydraulic Brake Systems -> General Motors -> Brake System Bleed -> Bleed Sequence -> Hydraulic System Flush -> Manual -> Pressure
Vehicle: 2003 Chevrolet Corvette Z06 5.7 V8 GAS
Manual
Pressure bleeding is recommended for all hydraulic systems. However, if a pressure bleeder is unavailable, use the following procedure. Brake fluid damages painted surfaces. Immediately clean any spilled fluid.
- Remove vacuum reserve by pumping brakes several times with engine off.
- Fill master cylinder reservoir with clean brake fluid. Do not let reservoir fall below half full during bleeding procedure.
- If required, bleed master cylinder as follows:
- Loosen master cylinder forward brake line connection until fluid flows from reservoir, then tighten brake line.
- Have assistant t...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Chevrolet Corvette cars and light trucks from 1990+.
Hydraulic Brake Systems -> General Motors -> Component Replacement -> Master Cylinder
Vehicle: 2003 Chevrolet Corvette Z06 5.7 V8 GAS
Master Cylinder
- On Vibe models, remove air filer hose clamp and hose from throttle body.
- On all models, disconnect fluid level sensor retainer and electrical connector.
- Drain master cylinder reservoir brake fluid into suita...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Tightening Specifications
Vehicle: 2003 Chevrolet Corvette 5.7 V8 GAS
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Chevrolet Corvette cars and light trucks from 1990+.
Hydraulic Brake Systems -> General Motors -> Component Service -> Assemble -> Aurora, Bonneville, Eighty-Eight, LeSabre, Park Avenue & Riviera -> Corvette -> CTS -> Disassemble -> Except Aurora, Bonneville, Corvette, CTS, Eighty-Eight, LeSabre, Park Avenue, Riviera & Vibe -> Master Cylinder Overhaul -> Vibe -> Wheel Cylinder Overhaul
Vehicle: 2003 Chevrolet Corvette 5.7 V8 GAS
Master Cylinder Overhaul
Except Aurora, Bonneville, Corvette, CTS, Eighty-Eight, LeSabre, Park Avenue, Riviera & Vibe
Disassemble
Refer to Figs. and , when performing the following procedures.
- Disconnect and plug hydraulic lines.
- Remove mounting nuts and master cylinder.
- Remove reservoir cover and diaphragm. Discard old brake fluid in reservoir.
- Inspect cover and diaphragm.
- Remove fluid level switch, if equipped.
- On models equipped with compact master cylinder, remove proportioner valve, Fig. .
- On all models, depress primary piston and remove lock ring.
- Plug primary fluid outlet (outlet...
CLICK HERE TO GET FULL ACCESS TO 2003 Chevrolet Corvette BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
