Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2003 Pontiac Vibe car and truck
repair procedures including Pontiac engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2003 Pontiac Vibe automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2003 Pontiac Vibe
- 2003 Pontiac Vibe GT 1.8 L4 GAS, CC:1795, Fuel Injection, Engine VIN:, Desg:L
- 2003 Pontiac Vibe 1.8 L4 GAS, CC:1794, Fuel Injection, Engine VIN:, Desg:8
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Pontiac Vibe AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Pontiac Vibe cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2003 Pontiac Vibe 1.8 L4 GAS
Front
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove engine under cover.
- Using a punch and a hammer, unstake staked part of lock nut.
- Remove drive shaft lock nut.
- Remove wheel speed sensor wire and brake hose retainer from strut assembly.
- Remove wheel speed sensor from steering knuckle.
- Disconnect outer tie rod end from steering knuckle.
- Disconnect lower ball joint from steering knuckle.
- Do not attempt to move vehicle with drive axle(s) removed from wheel bearing. Wheel(s) could fall off, dropping vehicle to ground and causing personal injury or damage to vehicle...
CLICK HERE TO GET FULL ACCESS TO 2003 Pontiac Vibe DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Pontiac Vibe AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Pontiac Vibe cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2003 Pontiac Vibe GT 1.8 L4 GAS
Front
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove engine under cover.
- Using a punch and a hammer, unstake staked part of lock nut.
- Remove drive shaft lock nut.
- Remove wheel speed sensor wire and brake hose retainer from strut assembly.
- Remove wheel speed sensor from steering knuckle.
- Disconnect outer tie rod end from steering knuckle.
- Disconnect lower ball joint from steering knuckle.
- Do not attempt to move vehicle with drive axle(s) removed from wheel bearing. Wheel(s) could fall off, dropping vehicle to ground and causing personal injury or damage to vehicle...
CLICK HERE TO GET FULL ACCESS TO 2003 Pontiac Vibe DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Pontiac Vibe AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Pontiac Vibe cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2003 Pontiac Vibe 1.8 L4 GAS
- Raise and support vehicle.
- Place a reference mark on pinion flange yoke and differential pinion flange.
- Remove four bolts and four nuts and washers.
- Remove mid shaft bearing support bolts.
- Remove slidi...
CLICK HERE TO GET FULL ACCESS TO 2003 Pontiac Vibe DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2003 Pontiac Vibe AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2003 Pontiac Vibe cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2003 Pontiac Vibe GT 1.8 L4 GAS
- Raise and support vehicle.
- Place a reference mark on pinion flange yoke and differential pinion flange.
- Remove four bolts and four nuts and washers.
- Remove mid shaft bearing support bolts.
- Remove slidi...
CLICK HERE TO GET FULL ACCESS TO 2003 Pontiac Vibe DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
