Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2003 Toyota Sequoia car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2003 Toyota Sequoia automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2003 Toyota Sequoia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Toyota Sequoia cars and light trucks from 1990+.
Toyota -> Hydraulic Brake Systems -> Component Service -> Assemble -> Disassemble -> Except Sienna -> Inspection -> Master Cylinder -> Overhaul -> Sienna -> Wheel Cylinders
Vehicle: 2003 Toyota Sequoia 4.7 V8 GAS
Master Cylinder
Except Sienna
Disassemble
For the following procedures, refer to Fig. for assistance.
- Remove master cylinder boot.
- Remove setscrew and reservoir tank, then the cap and strainer from reservoir.
- Remove two grommets and place cylinder in vise.
- Push piston in and remove stopper bolt, Fig. .
- Push pistons in and remove snap ring, then No. 1 piston carefully by hand.
- Place cylinder on edges of two wooden blocks and tap on cylinder until No. 2 piston comes out.
Inspection
Clean components with compressed air. Inspect cylinder bore for rust and scoring. Also, inspect for wear or ...
CLICK HERE TO GET FULL ACCESS TO 2003 Toyota Sequoia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Toyota Sequoia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Toyota Sequoia cars and light trucks from 1990+.
Toyota -> Power Brake Units -> Diagnosis & Testing -> Air Tightness Check -> Brake Booster Operational Test -> Operating Check
Vehicle: 2003 Toyota Sequoia 4.7 V8 GAS
Brake Booster Operational Test
Operating Check
- Depress brake pedal several times with engine stopped, and ensure pedal reserve distance has no change, Fig. .
- Depress brake pedal and start engine. If pedal drops slightly, operation is normal.
Air Tightness Check
- Start engine and stop after one or two minutes.
- Depress brake peda...
CLICK HERE TO GET FULL ACCESS TO 2003 Toyota Sequoia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Toyota Sequoia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Toyota Sequoia cars and light trucks from 1990+.
Toyota -> Hydraulic Brake Systems -> Brake System Bleed -> Brake Lines -> Master Cylinder
Vehicle: 2003 Toyota Sequoia 4.7 V8 GAS
Master Cylinder
- Fill reservoir with fluid.
- Disconnect tubes from master cylinder. Then slowly depress brake pedal and hold.
- Block off outlet holes with fingers, and release pedal. Repeat three or four times.
Brake Lines
Bleed wheel with longest brake line first, then work your way...
CLICK HERE TO GET FULL ACCESS TO 2003 Toyota Sequoia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Toyota Sequoia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Toyota Sequoia cars and light trucks from 1990+.
Toyota -> Power Brake Units -> Troubleshooting
Vehicle: 2003 Toyota Sequoia 4.7 V8 GAS
Refer to Fig. for gener...
CLICK HERE TO GET FULL ACCESS TO 2003 Toyota Sequoia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Toyota Sequoia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Toyota Sequoia cars and light trucks from 1990+.
Toyota -> Hydraulic Brake Systems -> Troubleshooting
Vehicle: 2003 Toyota Sequoia 4.7 V8 GAS
Refer to Fig. for gener...
CLICK HERE TO GET FULL ACCESS TO 2003 Toyota Sequoia BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2003 Toyota Sequoia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2003 Toyota Sequoia cars and light trucks from 1990+.
Toyota -> Power Brake Units -> Adjustments -> Brake Pedal Height & Freeplay
Vehicle: 2003 Toyota Sequoia 4.7 V8 GAS
Brake Pedal Height & Freeplay
Refer to Fig. for pedal height and freeplay references.
- Loosen stop light switch, then the clevis locknut.
- Adjust pedal height by turning pushrod.
- Tighten locknut an...
CLICK HERE TO GET FULL ACCESS TO 2003 Toyota Sequoia BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2003 Toyota Sequoia vehicle.
|
| Access the Complete guide! |
