Auto Parts Search
Toyota Sequoia CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Toyota REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Year
| 2010 | 2009 | 2008 | 2007 |
| 2006 | 2005 | 2004 | 2003 |
| 2002 | 2001 |
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about Toyota Sequoia car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Toyota Sequoia automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR Toyota Sequoia AUTOMOBILES
Air Conditioner and Heater Service Includes module configuration procedures, general service, maintenance, automatic temperature control, compressor services, electric cooling fans, vacuum diagrams, specifications, and manual air conditioning and heater diagnostics and replacement procedures for domestic and imported Toyota Sequoia cars and light trucks from 1990+
Import Compressor Service -> Zexel Compressor -> Compressor Clutch Service -> DKS-13CH, DKS-15CH & DKS-17CH Compressors -> DKS-16H Compressor -> DKV-14C & DKV-14D Compressor -> Replacement -> V-6 Compressor
Vehicle: 2001 Toyota Sequoia 4.7 V8 GAS
Replacement
DKV-14C & DKV-14D Compressor
- Install tool No. J-33939, or equivalent, hold clutch plate, then remove clutch assembly to shaft center bolt, Fig. .
- Install puller tool No. J-33944-A and forcing screw tool No. J-33944-4, or equivalents, remove driveplate, Fig. .
- Remove adjusting shims, Figs. and .
- Install snap ring pliers, remove snap ring.
- Remove pulley using a suitable puller, Fig. .
- Disconnect field coil lead wire, then remove field coil.
- Reverse procedure to install, noting the following:
-
...
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR Toyota Sequoia AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported Toyota Sequoia cars and light trucks from 1990+.
Disc Brakes -> Rear Disc & Parking Brakes -> Parking Brake Service -> Avalon, Camry, Camry Solara, Celica & Supra -> Land Cruiser & Sequoia -> Shoes, Replace
Vehicle: 2001 Toyota Sequoia 4.7 V8 GAS
Avalon, Camry, Camry Solara, Celica & Supra
Shoes, Replace
- Raise and support rear of vehicle, then remove tire and wheel assembly.
- Remove rear caliper.
- Remove rotor disc.
- Remove shoe return springs, Figs. and .
- Using strut remover 09717-20010, or equivalent, remove shoe strut and spring.
- Slide front shoe from under shoe hold-down spring, then remove shoe adjusting screw, tension spring and remove shoe.
- Slide rear from shoe hold-down spring, then disconnect parking brake cable from shoe lever.
- Apply non-melting grease on brake backing plate shoe flats, then on shoe sliding surface.
- ...
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR Toyota Sequoia AUTOMOBILES
Fuel filter replacement procedures with corresponding images for most domestic and imported Toyota Sequoia cars and light trucks sold in the U.S. for 1980+.
Toyota -> Fuel Filter Replacement -> Land Cruiser, Pickup, Previa, Sequoia, Tacoma, Tundra, T100, Truck & Van -> Fuel System Pressure Relief -> Models Less Union Bolt Fuel Line Connection -> Models w/Union Bolt Fuel Line Connection -> Removal & Installation
Vehicle: 2003 Toyota Sequoia 4.7 V8 GAS
Fuel System Pressure Relief
Models w/Union Bolt Fuel Line Connection
- Obtain the vehicle owners radio theft protection code prior to disconnecting the battery ground cable, if equipped.
- Disconnect the battery ground cable.
- Remove the fuel fill cap to release fuel tank pressure.
- Place a shop towel over the union bolt at top of fuel filter. Slowly loosen the union bolt allowing fuel pressure to bleed down.
- Whenever the union bolt is loosened to relieve fuel system pressure, always replace the bolt gasket.
Models Less Union Bolt Fuel...
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR Toyota Sequoia AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported Toyota Sequoia cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2010 Toyota Sequoia Platinum 5.7 V8 FLEX
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolt...
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR Toyota Sequoia AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported Toyota Sequoia cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures -> 2005-06 -> 2007-08 -> Initialization -> Registration -> TPMS Pressure Warning Valve & Transmitter
Vehicle: 2008 Toyota Sequoia SR5 5.7 V8 GAS
Initialization
2005-06
- Check and adjust tire pressure including spare to manufacturer's specifications.
- Turn the ignition switch to On position.
- Press and the hold tire pressure warning reset switch until warning lamp blinks three times at a one second interval.
- Initialization is completed in about 20 minutes when tire pressure warning ECU has received signals from all wheels including spare.
- Check that pressure for each tire is displayed in INIT THRESHOLD 1 to 5.
2007-08
Initialize the TPMS using a suitably programmed scan tool.
Registration
If replacing the TPMS ECU, prior to removal...
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR Toyota Sequoia AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported Toyota Sequoia cars and light trucks from 1990+.
Starter, Replace -> Flex Fuel -> Gasoline
Vehicle: 2009 Toyota Sequoia SR5 5.7 V8 FLEX
Flex Fuel
- Disconnect cable from battery ground terminal. Wait at least 90 seconds after disconnecting cable from ground (-) battery terminal to disable SRS system. When disconnecting cable, some systems need to be initialized after cable is reconnected.
- Remove engine under cover.
- Remove righthand front fender apron seal.
- Remove dipstick.
- Disconnect wire harness clamp.
- Remove bolt and dipstick guide.
- Remove O-ring from dipstick guide.
- Remove front exhaust pipe assembly.
- Remove front floor heat insulator.
- Remove exhaust manifold heat insulator.
- Remove righthand exhaust manifold sub-assembly...
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR Toyota Sequoia AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported Toyota Sequoia cars and light trucks sold in the U.S. from 1990+.
Toyota -> Malfunction Indicator Lamp (MIL) ->
Vehicle: 2009 Toyota Sequoia SR5 5.7 V8 GAS
On some models equipped with OBD II, the MIL will also illuminate if the fuel tank filler cap is not properly tightened. Tighten fuel tank filler cap until it clicks.
The MIL should light when the ignition switch is placed in the On position without starting the engine. When the engine is started, the lamp should go out. If it remains lit, a fault has been detected by the diagnostic system and has logged a diagnostic trouble code. If the fault does not occur again within three trips, the lamp will go out but a diagnostic tro...
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR Toyota Sequoia AUTOMOBILES
Includes radiator, cooling and heater hose replacement procedures for domestic and imported Toyota Sequoia cars and light trucks from 1990+
Radiator, Replace
Vehicle: 2008 Toyota Sequoia Platinum 5.7 V8 GAS
- Disconnect battery ground cable.
- Remove No. 1 engine under cover.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Remove front bumper cover assembly.
- On models with Trailer Towing System, remove No. 1 front bumper righthand side retainer sub-assembly.
- Remove oil cooler assembly.
- On all models, remove engine cover sub-assembly.
- Remove inlet radiator hose.
- Disconnect outlet radiator hose from water inlet housing.
- On models with Trailer Towing System, loosen four nuts holding fluid coupling and fan.
- Remove fan and generator V belt.
- Detach claw to open No....
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR Toyota Sequoia AUTOMOBILES
Serpentine belt replacement procedures with corresponding images for most domestic and imported Toyota Sequoia cars and light trucks sold in the U.S. from 1990+.
Serpentine Drive Belt, Replace
Vehicle: 2010 Toyota Sequoia Limited 5.7 V8 GAS
- Remove V-bank cover subassembly.
- Raise and support vehicle.
- Remove No. 1 engine under cover.
- Rotate tensioner pulley counterclockwise to loosen belt tension.
- While ...
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR Toyota Sequoia AUTOMOBILES
Component location diagrams for most Toyota Sequoia cars and light trucks sold in the U.S. from 1990+.
 Door Components Diagram for 2007 Toyota Sequoia Limited 4.7 V8 GASComponents on diagram: |
 Wireless Door Lock Control Components Diagram for 2006 Toyota Sequoia Limited 4.7 V8 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR Toyota Sequoia AUTOMOBILES
OEM drawn wiring diagrams for most Toyota Sequoia cars and light trucks sold in the U.S.
 2002 Toyota Sequoia 4.7 V8 GAS Wiring DiagramComponents on diagram: |
 2008 Toyota Sequoia Platinum 5.7 V8 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR Toyota Sequoia AUTOMOBILES
OEM TSB listings for most Toyota Sequoia cars and light trucks sold in the U.S. from 1985+.
|
Document: ABNORMAL RADIO FACEPLATE OPERATION Vehicle: 2008 Toyota Sequoia SR5 5.7 V8 GAS Auto Systems: |
|
Document: INTRODUCTION OF NEW AUTOMATIC TRANSMISSION FLUID - REVISED Vehicle: 2005 Toyota Sequoia SR5 4.7 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR Toyota Sequoia AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO Toyota Sequoia SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
