Auto Parts Search
2010 Toyota Sequoia CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Toyota REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Radiator & Hose Replacement
- Serpentine Belt Service
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2010 Toyota Sequoia AUTOMOBILES
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 2010 Toyota Sequoia Platinum 5.7 V8 FLEX
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with ...
CLICK HERE TO GET FULL ACCESS TO 2010 Toyota Sequoia DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2010 Toyota Sequoia AUTOMOBILES
Radiator, Replace
Vehicle: 2010 Toyota Sequoia SR5 5.7 V8 FLEX
- Disconnect battery ground cable.
- Remove No. 1 engine under cover.
- Drain cooling system into a suitable container.
- Remove front bumper cover assembly.
- On models with Trailer Towing System, remove No. 1 front bumper righthand side retainer sub-assembly.
- Remove oil cooler assembly.
- On all models, remove V-bank cover sub-assembly.
- Remove inlet radiator hose.
- Disconnect outlet radiator hose from water inlet housing.
- On models with Trailer Towing System, loosen four nuts holding fluid coupling and fan.
- Remove fan and generator V belt.
- Detach claw to open No. 1 flexible hose clamp.
- Disconnect re...
CLICK HERE TO GET FULL ACCESS TO 2010 Toyota Sequoia RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2010 Toyota Sequoia AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2010 Toyota Sequoia Limited 4.6 V8 GAS
- Remove V-Bank cover subassembly.
- Remove bolts from engine under cover assembly, then remove cover.
- Rotate or lift belt tensioner arm counterclockwise, using a suitable tool to...
CLICK HERE TO GET FULL ACCESS TO 2010 Toyota Sequoia SERPENTINE BELT SERVICE PROCEDURES
TECHNICAL SERVICE BULLETINS FOR 2010 Toyota Sequoia AUTOMOBILES
OEM TSB listings for most 2010 Toyota Sequoia cars and light trucks sold in the U.S. from 1985+.
Document: Oil Filter Cap Assembly Precautions Vehicle: 2010 Toyota Sequoia Limited 5.7 V8 GAS |
Document: LONG TERM VEHICLE STORAGE GUIDELINES Vehicle: 2010 Toyota Sequoia Limited 5.7 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2010 Toyota Sequoia TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2010 Toyota Sequoia AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2010 Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2010 Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2010 Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2010 Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2010 Toyota Sequoia SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2010 Toyota Sequoia vehicle. |
Access the Complete guide! |