Auto Parts Search
2006 Toyota Sequoia CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Toyota REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2006 Toyota Sequoia car and truck
repair procedures including Toyota engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Toyota Sequoia automobile. Try the Automotix DIY solution today!
FUEL FILTER REPLACEMENT PROCEDURES FOR 2006 Toyota Sequoia AUTOMOBILES
Toyota -> Fuel Filter Replacement -> Land Cruiser, Pickup, Previa, Sequoia, Tacoma, Tundra, T100, Truck & Van -> Fuel System Pressure Relief -> Models Less Union Bolt Fuel Line Connection -> Models w/Union Bolt Fuel Line Connection -> Removal & Installation
Vehicle: 2006 Toyota Sequoia SR5 4.7 V8 GAS
Fuel System Pressure Relief
Models w/Union Bolt Fuel Line Connection
- Obtain the vehicle owners radio theft protection code prior to disconnecting the battery ground cable, if equipped.
- Disconnect the battery ground cable.
- Remove the fuel fill cap to release fuel tank pressure.
- Place a shop towel over the union bolt at top of fuel filter. Slowly loosen the union bolt allowing fuel pressure to bleed down.
- Whenever the union bolt is loosened to relieve fuel system pressure, always replace the bolt gasket.
Models Less Union Bolt Fuel...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Toyota Sequoia AUTOMOBILES
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble -> Snap Ring Type
Vehicle: 2006 Toyota Sequoia SR5 4.7 V8 GAS
Disassemble
Snap Ring Type
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with ...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Toyota Sequoia AUTOMOBILES
Diagnosis & Testing -> 2005-06 -> 2007-08 -> Accessing Diagnostic Trouble Codes -> Clearing DTCs (Diagnostic Trouble Codes) -> Diagnostic Trouble Code Identification -> Reset Switch Test -> Using Scan Tool -> Using TPMS Warning Lamp
Vehicle: 2006 Toyota Sequoia SR5 4.7 V8 GAS
Accessing Diagnostic Trouble Codes
Using TPMS Warning Lamp
- Place the ignition switch in the Off position.
- Using Toyota SST or other suitable jumper, connect terminals TC and CG of DLC3. The DLC3 is located under the left side of the instrument panel, Fig. .
- Place the ignition switch in the On position.
- Read and note DTCs indicated by flashes of the TPMS warning lamp, Fig. .
- If the TPMS warning lamp blinks in .25 second intervals, a normal condition is indicated, Fig. .
- If the TPMS warning lamp blinks in .5 second intervals followed by a 1.5 second pause, then additional .5 second i...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2006 Toyota Sequoia AUTOMOBILES
Starter, Replace
Vehicle: 2006 Toyota Sequoia Limited 4.7 V8 GAS
- Disconnect battery ground cable. After removing battery ground cable wait 90 seconds to prevent air bag and seat belt pretensioner activation.
- Remove air pump assembly.
- Remove nut from righthand and lefthand wiper arm blade assembly.
- Release tabs from righthand and lefthand fender cowl seal.
- Remove clips securing righthand and lefthand cowl top ventilator louver subassembly.
- Disconnect electrical connector from wiper motor.
- Insert a suitable tool underneath wiper motor pivot arm and pry carefully upward to separate wiper link from wiper pivot arm. Upon installation put matchmarks on ...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Toyota Sequoia AUTOMOBILES
Toyota -> Automatic Transmission Overdrive Lamp ->
Vehicle: 2006 Toyota Sequoia Limited 4.7 V8 GAS
The "OD Off" lamp will be illuminated when the ignition switch is in the On position and the Overdrive (OD) switch is in the Off position. When the OD switch is placed in the On position, the "OD Off" lamp should go out. If the lamp flashes when the switch is placed in the On position, a fault has been detected by the electronic control system. After diagnosis and repair are c...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2006 Toyota Sequoia AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2006 Toyota Sequoia Limited 4.7 V8 GAS
Lower
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at radiator outlet.
- Remove hose from radiator.
- Reposition hose clamp at water inlet.
- Remove hose from water inlet.
- Remove hose from vehicle.
- Reverse procedure t...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2006 Toyota Sequoia AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2006 Toyota Sequoia Limited 4.7 V8 GAS
- Remove V-Bank cover subassembly.
- Remove bolts from engine under cover assembly, then remove cover.
- Rotate or lift belt tensioner arm counterclockwise, using a suitable tool to...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2006 Toyota Sequoia AUTOMOBILES
Component location diagrams for most 2006 Toyota Sequoia cars and light trucks sold in the U.S. from 1990+.
 Power Seat Control Components Diagram for 2006 Toyota Sequoia SR5 4.7 V8 GASComponents on diagram: |
 Power Door Lock Control Components Diagram for 2006 Toyota Sequoia SR5 4.7 V8 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2006 Toyota Sequoia AUTOMOBILES
OEM drawn wiring diagrams for most 2006 Toyota Sequoia cars and light trucks sold in the U.S.
 2006 Toyota Sequoia Limited 4.7 V8 GAS Wiring DiagramComponents on diagram: |
 2006 Toyota Sequoia Limited 4.7 V8 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2006 Toyota Sequoia AUTOMOBILES
OEM TSB listings for most 2006 Toyota Sequoia cars and light trucks sold in the U.S. from 1985+.
|
Document: A750E Transmission Extension Housing Seal Service Tip Vehicle: 2006 Toyota Sequoia Limited 4.7 V8 GAS Auto Systems: |
|
Document: TIRE PRESSURE MONITORING SYSTEM (TPMS) TIRE REGISTRATION "LOST COMMUNICATION WITH ECU" Vehicle: 2006 Toyota Sequoia Limited 4.7 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2006 Toyota Sequoia AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2006 Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2006 Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2006 Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2006 Toyota Sequoia cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Sequoia SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
