Auto Parts Search
We have info for following modifications of 2004 Ford Escape
- 2004 Ford Escape 3.0 V6 GAS, CID:182, Fuel Injection, Aspiration:182, Engine VIN:, Desg:1
- 2004 Ford Escape 2.0 L4 GAS, CC:1989, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:B
MAINTENANCE LAMP RESET PROCEDURES FOR 2004 Ford Escape AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2004 Ford Escape cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 2004 Ford Escape 2.0 L4 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 2004 Ford Escape MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2004 Ford Escape AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2004 Ford Escape cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Gauge Warning Lamp ->
Vehicle: 2004 Ford Escape 3.0 V6 GAS
This indicator should light if any of the following conditions appear:
- Engine oil pressure drops below approxi...
CLICK HERE TO GET FULL ACCESS TO 2004 Ford Escape MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2004 Ford Escape AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2004 Ford Escape cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 2004 Ford Escape 3.0 V6 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 2004 Ford Escape MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2004 Ford Escape AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2004 Ford Escape cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Anti-Lock Or Rear Anti-Lock Brake System Warning ->
Vehicle: 2004 Ford Escape 3.0 V6 GAS
Red and yellow indicator lamps are used to warn of system faults. The red lamp warns of such faults as low brake fluid level, parking brake On, system pressure differential and other system faults. The red indicator lamp will light for approximately two seconds during engine starting and should go off, unless parking brake is applied or a problem in the brake system exist. The red indicator lamp should reset after repairs to system have ...
CLICK HERE TO GET FULL ACCESS TO 2004 Ford Escape MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2004 Ford Escape AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2004 Ford Escape cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Engine Lamp -> 1998-2006 EEC-V -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool
Vehicle: 2004 Ford Escape 3.0 V6 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-V system. If the lamp remains On or starts to blink, a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
A temporary fault such as running out of fuel, poor quality or water in fuel or loose...
CLICK HERE TO GET FULL ACCESS TO 2004 Ford Escape MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2004 Ford Escape AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2004 Ford Escape cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Fuel Cap Lamp ->
Vehicle: 2004 Ford Escape 2.0 L4 GAS
The Check Fuel Cap Lamp will illuminate momentarily when the ignition switch is placed in the On position as a bulb check. If the lamp remains...
CLICK HERE TO GET FULL ACCESS TO 2004 Ford Escape MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2004 Ford Escape vehicle. |
Access the Complete guide! |