Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2005 GMC Yukon car and truck
repair procedures including GMC engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2005 GMC Yukon automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2005 GMC Yukon
- 2005 GMC Yukon SLE 4.8 V8 GAS, CID:294, Fuel Injection, Aspiration:294, Engine VIN:, Desg:V
- 2005 GMC Yukon SLE 5.3 V8 GAS, CID:323, Fuel Injection, Aspiration:323, Engine VIN:, Desg:T
- 2005 GMC Yukon SLE 5.3 V8 FLEX, CC:5328, CID:325, Fuel Injection, Aspiration:325, Engine VIN:, Desg:Z
- 2005 GMC Yukon SLT 4.8 V8 GAS, CID:294, Fuel Injection, Aspiration:294, Engine VIN:, Desg:V
- 2005 GMC Yukon SLT 5.3 V8 GAS, CID:323, Fuel Injection, Aspiration:323, Engine VIN:, Desg:T
- 2005 GMC Yukon SLT 5.3 V8 FLEX, CC:5328, CID:325, Fuel Injection, Aspiration:325, Engine VIN:, Desg:Z
BRAKE SERVICE PROCEDURES FOR 2005 GMC Yukon AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 GMC Yukon cars and light trucks from 1990+.
Hydraulic Brake Systems -> Adjustments -> Height Sensing Proportioning Valve
Vehicle: 2005 GMC Yukon SLE 5.3 V8 GAS
Height Sensing Proportioning Valve
The height sensing proportioning valve must be adjusted whenever the valve and/or linkage is disassembled or removed for service. In addition, adjustment should be inspected if excessive front wheel lock-up is experienced with a lower than desired brake application rate when vehicle is at or near maximum GVWR.
- Raise and support vehicle, leave wheels on and allow axle to hang freely.
- Remove lever retaining nut and disconnect lever from valve shaft, Fig. .
- Rotate valve shaft to permit installation of correct adjustment gauge, Fig. , ensure D shaped hol...
CLICK HERE TO GET FULL ACCESS TO 2005 GMC Yukon BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 GMC Yukon AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 GMC Yukon cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Brake System Bleed -> Hydraulic System Flush -> Manual Bleed -> Master Cylinder Bleed -> Pressure Bleed
Vehicle: 2005 GMC Yukon SLE 5.3 V8 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect and ...
CLICK HERE TO GET FULL ACCESS TO 2005 GMC Yukon BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 GMC Yukon AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 GMC Yukon cars and light trucks from 1990+.
Anti-Lock Brakes -> Kelsey-Hayes -> System Service -> Brake Pressure Modulator Valve (BPMV) -> Brake System Bleed -> Component Replacement -> Electronic Brake Control Module (EBCM) -> Front Wheel Speed Sensor -> Manual Bleed -> Pressure Bleed
Vehicle: 2005 GMC Yukon SLE 4.8 V8 GAS
Brake System Bleed
Gravity and vacuum bleeding procedures are not recommended for use with the anti-lock brake system. The manual bleed procedure is the preferred method, although pressure bleeding is also possible. Do not pump the brake pedal during the bleeding process, as fluid aeration may occur.
Manual Bleed
- Raise and support vehicle, then connect a clear plastic tube to brake bleed screw at righthand rear wheel.
- Place free end of tube in a glass jar partially filled with clean brake fluid. Ensure end of tube remains submerged in fluid and master cylinder reservoir is kept full.
- ...
CLICK HERE TO GET FULL ACCESS TO 2005 GMC Yukon BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 GMC Yukon AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 GMC Yukon cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Rotor, Replace
Vehicle: 2005 GMC Yukon SLE 5.3 V8 GAS
- Raise and support vehicle, then remove wheel and tire assemblies.
- Compress caliper pistons until they bottom in bores using suitable clamp.
- Remove calip...
CLICK HERE TO GET FULL ACCESS TO 2005 GMC Yukon BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 GMC Yukon AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 GMC Yukon cars and light trucks from 1990+.
Anti-Lock Brakes -> Kelsey-Hayes -> Description
Vehicle: 2005 GMC Yukon SLE 4.8 V8 GAS
When wheel slip is detected during a brake application, the ABS enters anti-lock mode. During anti-lock braking, hydraulic pressure in the individual wheel circuits is controlled to prevent any wheel from slipping. A separate hydraulic line and specific solenoid valves are provided for each wheel. The ABS can decrease, hold, or increase hydraulic pressure to each wheel brake. The ABS cannot, however, increase hydraulic pressure above the amount which is transmitted by the master cylinder during braking.
During anti-lock braking, a series of rapid pulsations is felt in the brake pedal...
CLICK HERE TO GET FULL ACCESS TO 2005 GMC Yukon BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2005 GMC Yukon AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2005 GMC Yukon cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Caliper Service -> Assemble -> Disassemble -> Inspection -> Installation -> Removal
Vehicle: 2005 GMC Yukon SLE 5.3 V8 GAS
Removal
- Siphon 2/3 of the brake fluid from master cylinder.
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Compress caliper pistons until they bottom in bores using suitable clamp, Fig. .
- Disconnect brake hose at caliper by removing inlet fitting bolt.
- Remove mounting bolts and caliper.
Inspection
Should it become required to remove the caliper for installation of new components, clean components in denatured alcohol, wipe dry using lint-free cloths. Blow out drilled passages and holes using compressed air. Inspect dust boots for punctures or tears. If punctures or tears are...
CLICK HERE TO GET FULL ACCESS TO 2005 GMC Yukon BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
