Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2005 Porsche Cayenne car and truck
repair procedures including Porsche engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2005 Porsche Cayenne automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2005 Porsche Cayenne
- 2005 Porsche Cayenne S 4.5 V8 GAS, CC:4511, Fuel Injection, Engine VIN:, Desg:B
- 2005 Porsche Cayenne Turbo 4.5 V8 GAS, CC:4511, Fuel Injection, Engine VIN:, Desg:C
- 2005 Porsche Cayenne 3.2 V6 GAS, CC:3189, CID:195, Fuel Injection, Aspiration:195, Engine VIN:, Desg:A
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Porsche Cayenne AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Porsche Cayenne cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2005 Porsche Cayenne S 4.5 V8 GAS
Front
- Raise and support vehicle.
- Remove engine guard.
- Remove three shield screws on all-wheel final drive. To undo cardan shaft screw connections, an assistant should sit in vehicle and block drive harness by activating footbrake.
- The colored markings, match points, on cardan shaft and on flange of rear final drive must be installed along a straight line. This neutralizes residual imbalance in components.
- Remove cardan shaft from front-axle final drive.
- Remove cardan shaft from transfer box. Screw threads used to fasten transmission cross member can pull out. Observe sequence of s...
CLICK HERE TO GET FULL ACCESS TO 2005 Porsche Cayenne DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Porsche Cayenne AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Porsche Cayenne cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2005 Porsche Cayenne Turbo 4.5 V8 GAS
Front
- Raise and support vehicle.
- Remove engine guard.
- Remove three shield screws on all-wheel final drive. To undo cardan shaft screw connections, an assistant should sit in vehicle and block drive harness by activating footbrake.
- The colored markings, match points, on cardan shaft and on flange of rear final drive must be installed along a straight line. This neutralizes residual imbalance in components.
- Remove cardan shaft from front-axle final drive.
- Remove cardan shaft from transfer box. Screw threads used to fasten transmission cross member can pull out. Observe sequence of s...
CLICK HERE TO GET FULL ACCESS TO 2005 Porsche Cayenne DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Porsche Cayenne AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Porsche Cayenne cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2005 Porsche Cayenne 3.2 V6 GAS
Front
- Raise and support vehicle.
- Remove engine guard.
- Remove three shield screws on all-wheel final drive. To undo cardan shaft screw connections, an assistant should sit in vehicle and block drive harness by activating footbrake.
- The colored markings, match points, on cardan shaft and on flange of rear final drive must be installed along a straight line. This neutralizes residual imbalance in components.
- Remove cardan shaft from front-axle final drive.
- Remove cardan shaft from transfer box. Screw threads used to fasten transmission cross member can pull out. Observe sequence of s...
CLICK HERE TO GET FULL ACCESS TO 2005 Porsche Cayenne DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Porsche Cayenne AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Porsche Cayenne cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2005 Porsche Cayenne Turbo 4.5 V8 GAS
Front
- Raise and support vehicle.
- Remove front wheel and underside panel.
- Release fastening nut for drive shaft.
- Push (press through) peg of drive shaft by approximately 3/4 to one inch into wheel hub with universal drive shaft/wheel hub extractor 87-1 or equivalent.
- Fix top axle strut with tension jack VW 552 or equivalent. This involves tensioning axle strut slightly because top ball joint can otherwise get damaged. By doing this, tension jack is mounted into top opening of wheel house (double panel) and in axle strut.
- Press out tie rod on wheel carrier with press-out tool T 1...
CLICK HERE TO GET FULL ACCESS TO 2005 Porsche Cayenne DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Porsche Cayenne AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Porsche Cayenne cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2005 Porsche Cayenne 3.2 V6 GAS
Front
- Raise and support vehicle.
- Remove front wheel and underside panel.
- Release fastening nut for drive shaft.
- Push (press through) peg of drive shaft by approximately 3/4 to one inch into wheel hub with universal drive shaft/wheel hub extractor 87-1 or equivalent.
- Fix top axle strut with tension jack VW 552 or equivalent. This involves tensioning axle strut slightly because top ball joint can otherwise get damaged. By doing this, tension jack is mounted into top opening of wheel house (double panel) and in axle strut.
- Press out tie rod on wheel carrier with press-out tool T 1...
CLICK HERE TO GET FULL ACCESS TO 2005 Porsche Cayenne DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2005 Porsche Cayenne AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2005 Porsche Cayenne cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2005 Porsche Cayenne S 4.5 V8 GAS
Front
- Raise and support vehicle.
- Remove front wheel and underside panel.
- Release fastening nut for drive shaft.
- Push (press through) peg of drive shaft by approximately 3/4 to one inch into wheel hub with universal drive shaft/wheel hub extractor 87-1 or equivalent.
- Fix top axle strut with tension jack VW 552 or equivalent. This involves tensioning axle strut slightly because top ball joint can otherwise get damaged. By doing this, tension jack is mounted into top opening of wheel house (double panel) and in axle strut.
- Press out tie rod on wheel carrier with press-out tool T 1...
CLICK HERE TO GET FULL ACCESS TO 2005 Porsche Cayenne DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2005 Porsche Cayenne vehicle.
|
| Access the Complete guide! |
