Auto Parts Search
2006 Ford Escape CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2006 Ford Escape car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Escape automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2006 Ford Escape AUTOMOBILES
Anti-Lock Brakes -> Escape & Mariner -> System Service -> ABS Control Module -> Accelerometer -> Anti-Lock Brakes -> Brake System Bleed -> Component Replacement -> Except Hybrid -> Front -> Gravity Bleed -> Hybrid -> Hydraulic Control Unit (HCU) -> Hydraulic Control Unit (HCU) Depressurization -> Manual Bleed -> Rear -> Wheel Speed Sensor
Vehicle: 2006 Ford Escape XLT 2.3 L4 GAS
Brake System Bleed
Except Hybrid
Anti-Lock Brakes
Bleeding the hydraulic control unit (HCU) is only required when removing or installing the HCU or master cylinder, or when opening the lines to the HCU. Carrying out the system bleed function drives trapped air from the HCU. Subsequent bleeding removes air from the brake hydraulic system through the bleeder screws.
- Connect suitable diagnostic scan tool.
- Access "System Bleed Function." Go to Tool Tab-Chassis-Braking-ABS Service Bleed and follow directions on scan tool.
- Manually bleed brake hydraulic system as outlined under "Manual Bleed."
- Re...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2006 Ford Escape AUTOMOBILES
Ford Motor Co. Light Trucks, SUVs & Vans -> Fuel Pressure Relief -> Escape & Mariner Hybrid
Vehicle: 2006 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS
The fuel system remains under high pressure even when the engine is not running. This residual pressure must be relieved before servicing the fuel system. To avoid injury or fire, release pressure from the fuel system before disconnecting any fuel line.
The fuel system pressure must be relieved prior to disconnecting fuel lines to prevent accidental spray of fuel.
After the battery has been disconnected and reconnected, some abnormal driveabilit...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Ford Escape AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2006 Ford Escape XLT 3.0 V6 GAS
Do not swap driveshaft assembles from different vehicles. The Escape Hybrid drive shaft is longer than the driveshaft in the Escape/Mariner and is not interchangeable.
- With vehicle in NEUTRAL, position it on a hoist.
- Remove ground strap bolt.
- Remove and discard 6 front driveshaft-to-transfer case bolts and washers. Do not reuse CV joint bolts and washers. Install new bolts and washers or damage to vehicle may occur.
- Index-mark front driveshaft to center bearing.
- Remove and discard 4 universal joint cap strap bolts and 2 cap straps and remove front driveshaft. Do not reuse bolts a...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Ford Escape AUTOMOBILES
Reset Procedures
Vehicle: 2006 Ford Escape XLS 2.3 L4 GAS
If the system detects low tire pressure, CHECK TIRE PRESSURE lamp will illuminate. Inflating tire(s) to recommended pressure will clear the tire ...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2006 Ford Escape AUTOMOBILES
Alternator, Replace
Vehicle: 2006 Ford Escape XLT 3.0 V6 GAS
- Disconnect battery ground cable.
- Remove righthand front brake rotor.
- Remove and discard righthand front axle wheel hub nut.
- Release tie rod end from righthand steering knuckle using a suitable tie rod end removal tool.
- Remove lower ball joint pinch bolt and nut, then release righthand lower ball joint from steering knuckle.
- Separate righthand halfshaft from front wheel knuckle, using suitable front hub removal tool, then remove halfshaft.
- Remove intermediate shaft retainer nuts, then righthand intermediate shaft.
- Remove righthand lower splash shield screws and pin type retainers, t...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2006 Ford Escape AUTOMOBILES
Cabin Air Filter Service -> Ford Motor Co. -> 2005-07 Escape, Escape Hybrid, Mariner & Mariner Hybrid
Vehicle: 2006 Ford Escape XLS 2.3 L4 GAS
Under normal operating conditions the cabin air filter should be replaced every 15,000 miles. In dusty areas change the cabin air filter more often.
- Remove the two wiper pivot arms nuts, cowl panel grille pin-type retainers and cowl panel grille pin-type retainers, Fi...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Ford Escape AUTOMOBILES
Ford Motor Co. Trucks -> Tire Pressure Monitoring System (TPMS) Warning Indicator -> 2006-09 Escape & Escape Hybrid -> Relearn -> Reset -> TPMS Sensor Activation -> TPMS Sensor Training
Vehicle: 2006 Ford Escape XLS 2.3 L4 GAS
Reset
If the system detects low tire pressure, CHECK TIRE PRESSURE lamp will illuminate. Inflating tire(s) to recommended pressure will clear the tire message. Up to two minutes of driving above 20 mph may be required for the warning lamp to turn OFF after the tires have been filled to the recommended pressure.
Relearn
TPMS Sensor Activation
To conserve battery power, the TPMS sensors will go into a sleep mode after approximately 30 minutes of inactivity. The sensors will not transmit tire pressure information while in sleep mode. The sensors must be activated to tran...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2006 Ford Escape AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2006 Ford Escape XLS 2.3 L4 GAS
Lower
- Drain cooling system into a suitable container.
- Reposition hose clamp from radiator.
- Remove radiator outlet hose from radiator.
- Reposition hose clamp from coolant pump.
- Remove radiator outlet hose from coolant pump and from vehicle.
- Reverse p...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2006 Ford Escape AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2006 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS
- Raise and support vehicle, remove righthand front tire and wheel assembly.
- Remove righthand front lo...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2006 Ford Escape AUTOMOBILES
Component location diagrams for most 2006 Ford Escape cars and light trucks sold in the U.S. from 1990+.
 Connectors and Splices Diagram for 2006 Ford Escape Hybrid 2.3 L4 ELECTRIC/GASComponents on diagram: |
 Wiring Harness Diagram for 2006 Ford Escape Limited 3.0 V6 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2006 Ford Escape AUTOMOBILES
OEM drawn wiring diagrams for most 2006 Ford Escape cars and light trucks sold in the U.S.
 2006 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS Wiring DiagramComponents on diagram: |
 2006 Ford Escape Limited 3.0 V6 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2006 Ford Escape AUTOMOBILES
OEM TSB listings for most 2006 Ford Escape cars and light trucks sold in the U.S. from 1985+.
|
Document: Red Triangle On and Stop Safely Now Message - DTC P1A0C Vehicle: 2006 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS Symptoms: |
|
Document: LOWER CONTROL ARM BUSHING INSPECTION PROCEDURE Vehicle: 2006 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2006 Ford Escape AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2006 Ford Escape cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2006 Ford Escape cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2006 Ford Escape cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2006 Ford Escape cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Escape SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2006 Ford Escape vehicle.
|
| Access the Complete guide! |
