Auto Parts Search
2006 Ford Mustang CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2006 Ford Mustang car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Mustang automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2006 Ford Mustang AUTOMOBILES
Disc Brakes -> Front Disc Brakes -> Description -> Dual Piston Calipers -> Single Piston Calipers
Vehicle: 2006 Ford Mustang GT 4.6 V8 GAS
Dual Piston Calipers
The caliper consists of a sliding bridge type caliper housing with dual pistons, caliper mounting frame and inner and outer friction pad assemblies, Figs. and . The caliper is located into and slides on the anchor frame by its thrust face and a locating pin and clip. The friction pads are retained into the anchor frame by the caliper sliding bridge assembly and use an anti-rattle spring clip to reduce brake noise. The friction pads are retained into the sliding bridge assembly by clips located on the back of the friction pad.
Lefthand and righthand caliper and in...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2006 Ford Mustang AUTOMOBILES
Ford Motor Co. Passenger Cars -> Fuel Filter Replacement -> Except 2002-05 Thunderbird, 2000-06 LS, 1984-87 Escort, Tracer, Tempo & Topaz 2.0L Diesel Engine & 1984-85 Continental & Mark VI 2.4L Diesel Engine
Vehicle: 2006 Ford Mustang GT 4.6 V8 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent accidental spray of fuel.
When installing the fuel filter, ensure the flow arrow is facing in the pro...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Ford Mustang AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2006 Ford Mustang 4.0 V6 GAS
- Raise and support vehicle.
- Mark driveshaft for installation alignment.
- Remove eight driveshaft flange bolts, Fig. .
- Disconnect driveshaft flanges from pilots and remove driveshaft using suitable tool, Fig. . Driveshaft flanges fits tightly on pilots. Never hammer on driveshaft or any of its components to disconnect flanges from pilots. Pry ...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2006 Ford Mustang AUTOMOBILES
Alternator, Replace
Vehicle: 2006 Ford Mustang GT 4.6 V8 GAS
- Disconnect battery ground cable.
- Press lock tab, remove crankcase vent tube from air cleaner outlet pipe and position it aside.
- Loosen clamp, remove air cleaner outlet pipe from throttle body and position it aside.
- Rotate tensioner clockwise and position front end accessory drive belt aside.
- Remove alternator mounting bolts.
- Remove alternator outer bracket bolts and position alternator aside...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2006 Ford Mustang AUTOMOBILES
Cabin Air Filter Service -> Ford Motor Co. -> 2002-05 Thunderbird & 2005-09 Mustang
Vehicle: 2006 Ford Mustang 4.0 V6 GAS
Under normal operating conditions the cabin air filter should be replaced every 15,000 miles. In dusty areas change the cabin air filter more often.
- Open the hood.
- Remove the lefthand and righthand cowl trim pieces.
- Note position of wiper blades on windshield.
- Remove the wiper arm nut covers, then the nuts and wiper arms.
- Remove the pin type retainers attaching the cowl cover to the cowl, Fig. .
- Release the righthand corner of the cabin air filter by pushing on the retaining cl...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Ford Mustang AUTOMOBILES
Ford Motor Co. Cars -> Powertrain Malfunction Indicator ->
Vehicle: 2006 Ford Mustang GT 4.6 V8 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected in the powertrain system. If the lamp remains On a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Powertrain Malfunction Indicator will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2006 Ford Mustang AUTOMOBILES
Radiator, Replace
Vehicle: 2006 Ford Mustang 4.0 V6 GAS
- Drain cooling system into suitable container.
- Remove four push pin retainers and air deflector.
- Disconnect crankcase vent tube from air cleaner outlet pipe.
- Loosen two clamps and remove air cleaner outlet pipe.
- Remove mounting bolt and position power steering reservoir aside, Fig. .
- Remove two mounting bolts and position degas bottle aside.
- Detach and position lower degas bottle hose aside.
- Disconnect cooling fan motor and shroud e...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2006 Ford Mustang AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2006 Ford Mustang 4.0 V6 GAS
- Rotate or lift the belt tensioner arm, using a suitable tool to relieve tension from dr...
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2006 Ford Mustang AUTOMOBILES
Component location diagrams for most 2006 Ford Mustang cars and light trucks sold in the U.S. from 1990+.
 Air Bag and Safety Belt Pretensioner Supplemental Restraint System Diagram for 2006 Ford Mustang GT 4.6 V8 GASComponents on diagram: |
 A-Pillar Diagram for 2006 Ford Mustang 4.0 V6 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2006 Ford Mustang AUTOMOBILES
OEM drawn wiring diagrams for most 2006 Ford Mustang cars and light trucks sold in the U.S.
 2006 Ford Mustang 4.0 V6 GAS Wiring DiagramComponents on diagram: |
 2006 Ford Mustang GT 4.6 V8 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2006 Ford Mustang AUTOMOBILES
OEM TSB listings for most 2006 Ford Mustang cars and light trucks sold in the U.S. from 1985+.
|
Document: WATER LEAK - FRONT FLOOR AREA - REVISED Vehicle: 2006 Ford Mustang 4.0 V6 GAS Symptoms: |
|
Document: A-PILLAR RATTLE NOISE Vehicle: 2006 Ford Mustang 4.0 V6 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2006 Ford Mustang AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2006 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2006 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2006 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2006 Ford Mustang cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2006 Ford Mustang SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2006 Ford Mustang vehicle.
|
| Access the Complete guide! |
