Auto Parts Search
2006 GMC Canyon CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT GMC REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
BRAKE SERVICE PROCEDURES FOR 2006 GMC Canyon AUTOMOBILES
Hydraulic Brake Systems -> Brake System Bleed -> Hydraulic System Flush -> Manual Bleed -> Master Cylinder Bleed -> Parking Brake Bleed -> Pressure Bleed
Vehicle: 2006 GMC Canyon SLE 3.5 L5 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect and ...
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2006 GMC Canyon AUTOMOBILES
General Motors Corp./Saturn Light Trucks, SUVs & Vans -> Fuel Filter Scheduled Maintenance -> Colorado & Canyon -> Normal Service -> Severe Service
Vehicle: 2006 GMC Canyon SLE 2.8 L4 GAS
Normal Service
Service as...
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 GMC Canyon AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2006 GMC Canyon SLE 3.5 L5 GAS
- Raise and support vehicle.
- Remove wheel and tire assembly.
- Remove wheel drive shaft nut and washer. Do not reuse wheel drive shaft nut, replace with new.
- Remove steering knuckle assembly.
- Release wheel drive shaft by placing a brass drift against tripod housing. Firmly strike brass drift with a hammer to release drive shaft.
- Remove front wheel drive shaft from vehicle.
- Reverse procedure to install, noting the following:
- A snap or po...
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2006 GMC Canyon AUTOMOBILES
Starter, Replace
Vehicle: 2006 GMC Canyon WT 2.8 L4 GAS
Upon removal of starter, note if any shims are used. If shims are used, they should be installed in their original locations. After installation, if starter is noisy during cranking, remove one .015 inch double shim or add one .015 inch single shim to the outer bolt. If starter makes a high pitched whine after firing, add .015 inch double shims until noise ceases.
- Disconnect battery ground cable.
- Remove intake manifold.
- Remove st...
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 GMC Canyon AUTOMOBILES
General Motors Corp./Saturn Trucks -> Anti-Lock Brake System Warning Lamp ->
Vehicle: 2006 GMC Canyon SL 2.8 L4 GAS
This lamp should light for approximately 6-8 seconds when the ignition is turned On as a bulb check. If the warn...
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2006 GMC Canyon AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2006 GMC Canyon SL 2.8 L4 GAS
Inlet
- Drain cooling system into a suitable container.
- Reposition heater core inlet hose clamp at engine block.
- Remove hose from engine block.
- Reposition heater hose inlet clamp at heater core.
- Remove heater inlet hose from heater core.
- Remove hose from vehicle.
- Reverse procedure to install.
Outlet
- Drai...
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2006 GMC Canyon AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2006 GMC Canyon SL 2.8 L4 GAS
- Rotate tensioner clockwise with a suitable 3/8 inch breaker bar.
- Remove belt from water pump pul...
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2006 GMC Canyon AUTOMOBILES
Component location diagrams for most 2006 GMC Canyon cars and light trucks sold in the U.S. from 1990+.
Inside Rearview Mirror Diagram for 2006 GMC Canyon SL 2.8 L4 GAS Components on diagram: |
Passenger Compartment Diagram for 2006 GMC Canyon SLT 3.5 L5 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2006 GMC Canyon AUTOMOBILES
OEM drawn wiring diagrams for most 2006 GMC Canyon cars and light trucks sold in the U.S.
2006 GMC Canyon WT 3.5 L5 GAS Wiring Diagram Components on diagram: |
2006 GMC Canyon SLE 2.8 L4 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2006 GMC Canyon AUTOMOBILES
OEM TSB listings for most 2006 GMC Canyon cars and light trucks sold in the U.S. from 1985+.
Document: Engine Rattle Noise after R And R of the Crankshaft Balancer -Inspect Bolt Torque Vehicle: 2006 GMC Canyon SLE 2.8 L4 GAS Symptoms: |
Document: GM of Canada New Vehicle Limited Warranty Tire Program Vehicle: 2006 GMC Canyon SLE 2.8 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2006 GMC Canyon AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2006 GMC Canyon cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2006 GMC Canyon cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2006 GMC Canyon cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2006 GMC Canyon cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2006 GMC Canyon SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2006 GMC Canyon vehicle. |
Access the Complete guide! |