Auto Parts Search
We have info for following modifications of 2006 Mercury Mariner
- 2006 Mercury Mariner Premier 3.0 V6 GAS, CID:183, Fuel Injection, Aspiration:183, Engine VIN:, Desg:1
- 2006 Mercury Mariner Hybrid 2.3 L4 ELECTRIC/GAS, CID:140, Fuel Injection, Aspiration:140, Engine VIN:, Desg:H
- 2006 Mercury Mariner Convenience 2.3 L4 GAS, CID:140, Fuel Injection, Aspiration:140, Engine VIN:, Desg:Z
- 2006 Mercury Mariner Luxury 3.0 V6 GAS, CID:183, Fuel Injection, Aspiration:183, Engine VIN:, Desg:1
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Mercury Mariner cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Rear Load Leveling (CHECK SUSP) ->
Vehicle: 2006 Mercury Mariner Premier 3.0 V6 GAS
The CHECK SUSP indicator lights when there is a fault of the rear load ...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Mercury Mariner cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Engine Lamp -> 1998-2006 EEC-V -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool
Vehicle: 2006 Mercury Mariner Convenience 2.3 L4 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-V system. If the lamp remains On or starts to blink, a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
A temporary fault such as running out of fuel, poor quality or water in fuel or loose...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Mercury Mariner cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Tire Pressure Monitoring System (TPMS) Warning Indicator -> 2006-09 Escape & Escape Hybrid -> Relearn -> Reset -> TPMS Sensor Activation -> TPMS Sensor Training
Vehicle: 2006 Mercury Mariner Hybrid 2.3 L4 ELECTRIC/GAS
Reset
If the system detects low tire pressure, CHECK TIRE PRESSURE lamp will illuminate. Inflating tire(s) to recommended pressure will clear the tire message. Up to two minutes of driving above 20 mph may be required for the warning lamp to turn OFF after the tires have been filled to the recommended pressure.
Relearn
TPMS Sensor Activation
To conserve battery power, the TPMS sensors will go into a sleep mode after approximately 30 minutes of inactivity. The sensors will not transmit tire pressure information while in sleep mode. The sensors must be activated to tran...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Mercury Mariner cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Engine Oil Life Indicator -> Mariner & Mariner Hybrid
Vehicle: 2006 Mercury Mariner Luxury 3.0 V6 GAS
- Press and release SETUP button until System Check is displayed.
- Press SETUP button again to displ...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Mercury Mariner cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Low Fuel Level Warning Lamp ->
Vehicle: 2006 Mercury Mariner Luxury 3.0 V6 GAS
When fuel level drops below a predetermined level, the CHECK GAUGE indicator should light. The CHECK GAUGE indicator shoul...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2006 Mercury Mariner cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 2006 Mercury Mariner Convenience 2.3 L4 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2006 Mercury Mariner vehicle. |
Access the Complete guide! |