Auto Parts Search
2006 Mercury Mariner CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Mercury REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2006 Mercury Mariner car and truck
repair procedures including Mercury engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Mercury Mariner automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Anti-Lock Brakes -> Escape & Mariner -> Diagnosis & Testing -> 2002-04 -> 2005-06 -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation -> Inspection & Verification -> Pinpoint Tests
Vehicle: 2006 Mercury Mariner Luxury 3.0 V6 GAS
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool and Vehicle Communication Module (VCM) with appropriate adapters, or equivalents, to the Data Link Connector (DCL) located in the passenger compartment beneath the instrument panel. Follow tool manufacturer's instructions for accessing Diagnostic Trouble Codes (DTC).
Diagnostic Trouble Code Interpretation
Refer to Figs. and for diagnostic trouble code interpretation.
Diagnostic Tests
Inspection & Verification
Verify concern by applying brakes under different conditions. Inspect for obvious signs of me...
[[table data]] [[table data]]CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Ford Motor Co. Light Trucks, SUVs & Vans -> Fuel Filter Replacement -> Except Diesel Engines & Villager
Vehicle: 2006 Mercury Mariner Luxury 3.0 V6 GAS
The fuel system remains under high pressure even when the engine is not running. This residual pressure must be relieved before servicing the fuel system. To avoid injury or fire, release pressure from the fuel system before disconnecting any fuel line.
The fuel system pressure must be relieved prior to disconnecting fuel lines to prevent accidental spray of fuel.
After the battery has been disconnected and reconnected, some abnormal driveability symptoms may occur. The vehicle may need to be driven 10 miles or more while it relearns its adaptive strategy.
On model...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2006 Mercury Mariner Hybrid 2.3 L4 ELECTRIC/GAS
Do not swap driveshaft assembles from different vehicles. The Escape Hybrid drive shaft is longer than the driveshaft in the Escape/Mariner and is not interchangeable.
- With vehicle in NEUTRAL, position it on a hoist.
- Remove ground strap bolt.
- Remove and discard 6 front driveshaft-to-transfer case bolts and washers. Do not reuse CV joint bolts and washers. Install new bolts and washers or damage to vehicle may occur.
- Index-mark front driveshaft to center bearing.
- Remove and discard 4 universal joint cap strap bolts and 2 cap straps and remove front driveshaft. Do not reuse bolts a...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Component Replacement -> Installation -> Pressure Monitor Sensor (Strap & Cradle Type) -> Pressure Monitor Sensor (Valve Stem Type) -> Removal
Vehicle: 2006 Mercury Mariner Convenience 2.3 L4 GAS
Pressure Monitor Sensor (Valve Stem Type)
Use only Ford tool no. 204-354, or equivalent, anytime tire pressures are measured to be sure that accurate values are obtained. Place air chuck straight on the valve stem to inflate tire. Do not cock air chuck during inflation cycle. Doing so can damage valve stem and cause air leaks. Ford recommends using a round head air chuck on tire pressure sensors; it is not recommended to use air chucks with long shanks. Doing so can cause tire pressure sensor valve stem damage and loss of tire pressure.
- Remove wheel and tire assembly.
- With...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Alternator, Replace
Vehicle: 2006 Mercury Mariner Premier 3.0 V6 GAS
- Disconnect battery ground cable.
- Remove righthand front brake rotor.
- Remove and discard righthand front axle wheel hub nut.
- Release tie rod end from righthand steering knuckle using a suitable tie rod end removal tool.
- Remove lower ball joint pinch bolt and nut, then release righthand lower ball joint from steering knuckle.
- Separate righthand halfshaft from front wheel knuckle, using suitable front hub removal tool, then remove halfshaft.
- Remove intermediate shaft retainer nuts, then righthand intermediate shaft.
- Remove righthand lower splash shield screws and pin type retainers, t...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Cabin Air Filter Service -> Ford Motor Co. -> 2005-07 Escape, Escape Hybrid, Mariner & Mariner Hybrid
Vehicle: 2006 Mercury Mariner Hybrid 2.3 L4 ELECTRIC/GAS
Under normal operating conditions the cabin air filter should be replaced every 15,000 miles. In dusty areas change the cabin air filter more often.
- Remove the two wiper pivot arms nuts, cowl panel grille pin-type retainers and cowl panel grille pin-type retainers, Fi...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Ford Motor Co. Trucks -> Check Fuel Cap Lamp ->
Vehicle: 2006 Mercury Mariner Luxury 3.0 V6 GAS
The Check Fuel Cap Lamp will illuminate momentarily when the ignition switch is placed in the On position as a bulb check. If the lamp remains...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Radiator, Replace
Vehicle: 2006 Mercury Mariner Luxury 3.0 V6 GAS
- Raise and support vehicle.
- Drain cooling system into suitable container.
- Remove lower splash shields.
- Disconnect lower radiator hose and high pressure transmission line. Plug trans line.
- Lower vehicle.
- Disconnect transmission return line. Plug trans line...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2006 Mercury Mariner AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2006 Mercury Mariner Hybrid 2.3 L4 ELECTRIC/GAS
- Rotate counterclockwise the belt tensioner arm, using a suitable tool to relieve tension fro...
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2006 Mercury Mariner AUTOMOBILES
Component location diagrams for most 2006 Mercury Mariner cars and light trucks sold in the U.S. from 1990+.
 Transmission Diagram for 2006 Mercury Mariner Hybrid 2.3 L4 ELECTRIC/GASComponents on diagram: |
 Complete Vehicle Diagram for 2006 Mercury Mariner Luxury 3.0 V6 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2006 Mercury Mariner AUTOMOBILES
OEM drawn wiring diagrams for most 2006 Mercury Mariner cars and light trucks sold in the U.S.
 2006 Mercury Mariner Convenience 2.3 L4 GAS Wiring DiagramComponents on diagram: |
 2006 Mercury Mariner Hybrid 2.3 L4 ELECTRIC/GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2006 Mercury Mariner AUTOMOBILES
OEM TSB listings for most 2006 Mercury Mariner cars and light trucks sold in the U.S. from 1985+.
|
Document: LOWER CONTROL ARM BUSHING INSPECTION PROCEDURE Vehicle: 2006 Mercury Mariner Premier 3.0 V6 GAS Auto Systems: |
|
Document: Noise - Front Strut Area Vehicle: 2006 Mercury Mariner Premier 3.0 V6 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2006 Mercury Mariner AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2006 Mercury Mariner cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2006 Mercury Mariner cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2006 Mercury Mariner cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2006 Mercury Mariner cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2006 Mercury Mariner SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
