Auto Parts Search
We have info for following modifications of 2006 Toyota Tundra
- 2006 Toyota Tundra 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285
- 2006 Toyota Tundra 4.0 V6 GAS, CC:3956, Fuel Injection
- 2006 Toyota Tundra Limited 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285
- 2006 Toyota Tundra SR5 4.7 V8 GAS, CC:4663, CID:285, Fuel Injection, Aspiration:285
- 2006 Toyota Tundra SR5 4.0 V6 GAS, CC:3956, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Toyota Tundra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Toyota Tundra cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2006 Toyota Tundra SR5 4.7 V8 GAS
Front
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove bolts and heat insulator bracket.
- Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolts, nuts, and washers from differential flange.
- Remove two bolts and two adjusting washers and disconnect driveline with center bearing shaft.
- Place reference mark on driveline and transfer flange. Paint is recommended for match marks. Never damage r...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Toyota Tundra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Toyota Tundra cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2006 Toyota Tundra Limited 4.7 V8 GAS
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- On models equipped with 4WD, drain differential oil into suitable container.
- On all models, remove hub cap and cotter pin.
- Apply brakes and remove lefthand driveline hub nut.
- Remove bolt and nuts and separate lefthand front suspension arm subassembly from lower ball joint.
- Disengage driveshaft from axle hub using plastic hammer.
- Push steering knuckle outward and disconnect driveshaft from stee...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Toyota Tundra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Toyota Tundra cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2006 Toyota Tundra 4.7 V8 GAS
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- On models equipped with 4WD, drain differential oil into suitable container.
- On all models, remove hub cap and cotter pin.
- Apply brakes and remove lefthand driveline hub nut.
- Remove bolt and nuts and separate lefthand front suspension arm subassembly from lower ball joint.
- Disengage driveshaft from axle hub using plastic hammer.
- Push steering knuckle outward and disconnect driveshaft from stee...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Toyota Tundra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Toyota Tundra cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble
Vehicle: 2006 Toyota Tundra 4.0 V6 GAS
Disassemble
This procedure describes a driveline equipped with cardan joint in tube yoke. Driveline equipped with companion/slip yoke repeat steps to remove remaining cardan joint.
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke using suitable tool.
- Position yoke with grease fitting pointing up, if equipped.
- Position socket with an inside diam...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Toyota Tundra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Toyota Tundra cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2006 Toyota Tundra SR5 4.7 V8 GAS
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- On models equipped with 4WD, drain differential oil into suitable container.
- On all models, remove hub cap and cotter pin.
- Apply brakes and remove lefthand driveline hub nut.
- Remove bolt and nuts and separate lefthand front suspension arm subassembly from lower ball joint.
- Disengage driveshaft from axle hub using plastic hammer.
- Push steering knuckle outward and disconnect driveshaft from stee...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2006 Toyota Tundra AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2006 Toyota Tundra cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2006 Toyota Tundra 4.7 V8 GAS
Front
- Place vehicle in neutral.
- Release parking brake.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove bolts and heat insulator bracket.
- Place reference mark on driveline and differential flange. Paint is recommended for match marks. Never damage rear driveline shaft differential flange.
- Remove bolts, nuts, and washers from differential flange.
- Remove two bolts and two adjusting washers and disconnect driveline with center bearing shaft.
- Place reference mark on driveline and transfer flange. Paint is recommended for match marks. Never damage r...
CLICK HERE TO GET FULL ACCESS TO 2006 Toyota Tundra DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2006 Toyota Tundra vehicle. |
Access the Complete guide! |