Auto Parts Search
2007 Chrysler 300 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Chrysler REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2007 Chrysler 300 car and truck
repair procedures including Chrysler engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Chrysler 300 automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2007 Chrysler 300 AUTOMOBILES
Power Brake Units -> Diagnosis & Testing
Vehicle: 2007 Chrysler 300 Limited 3.5 V6 GAS
Refer to Fig. for p...
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Chrysler 300 AUTOMOBILES
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Chrysler 300 Touring 3.5 V6 GAS
Front
Halfshaft inner and outer boots are not serviceable separately. Boot replacement requires entire shaft assembly replacement.
Lefthand halfshaft is shorter than right. Identify and tag halfshafts upon removal to ensure proper installation.
- Raise and support vehicle, then remove tire and wheel assembly.
- While holding link ball joint stem from rotating, remove stabilizer link to shock clevis bracket nut.
- Slide link ball joint stem from clevis bracket.
- Remove clevis bracket to bottom of shock nut and pinch bolt.
- Remove shock clevis bracket to lower control arm nut and bolt.
- Pul...
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2007 Chrysler 300 AUTOMOBILES
Component Replacement -> Front -> Installation -> Rear -> Removal -> Tire Pressure Sensor -> Tire Pressure Transponder
Vehicle: 2007 Chrysler 300 Touring 3.5 V6 GAS
Tire Pressure Sensor
The cap used on this valve stem contains an O-ring seal to prevent contamination and moisture from entering the valve stem. Retain this valve stem cap for reuse. Do not substitute a regular valve stem cap in its place.
The valve stem used on this vehicle is made of aluminum and the core is nickel plated brass. The original valve stem core must be reinstalled and not substituted with a valve stem core made of a different material. This is required to prevent corrosion in the valve stem caused by the different metals.
Removal
- Raise and support vehicle with ...
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2007 Chrysler 300 AUTOMOBILES
Starter, Replace
Vehicle: 2007 Chrysler 300 C 5.7 V8 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- On models equipped with AWD, proceed as follows:
- Remove steering gear to steering column pinch bolt.
- Remove three mounting bolts and slightly lower steering gear.
- Temporarily support steering gear. Do not disconnect any hydraulic hoses or remove steering linkage.
- Remove steering gear heat-shield.
- On all models, while supporting starter, remove mount...
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2007 Chrysler 300 AUTOMOBILES
Cabin Air Filter Service -> Chrysler LLC -> 2005-09 300, Magnum, 2006-09 Charger & 2008-09 Challenger
Vehicle: 2007 Chrysler 300 Touring 3.5 V6 GAS
The cabin air filter should be replaced every 12,000 miles.
- Open the hood.
- Remove the passenger side air inlet grille from the cowl panel, Fig. .
- Open the cabin air filter door.
- Remove the cabin air filter from the filter housing...
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2007 Chrysler 300 AUTOMOBILES
Chrysler LLC Cars -> Anti-Lock Brake System (ABS) Warning Lamp -> Charger, Magnum & 300C
Vehicle: 2007 Chrysler 300 C 5.7 V8 GAS
This light monitors the Anit-Lock Brake System. The light will turn On when the ignition switch is turned to the On position and may stay On for as long as 4 seconds. If the ABS light remains On or turns On while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required....
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2007 Chrysler 300 AUTOMOBILES
Radiator, Replace
Vehicle: 2007 Chrysler 300 2.7 V6 GAS
- Drain cooling system into suitable container.
- Remove upper radiator hose.
- Remove upper radiator closure panels.
- Disconnect cooling fan electrical connector, then remove mounting bolts and cooling fan.
- Raise and support vehicle.
- Remove lower splash shield.
- Remove lower radi...
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2007 Chrysler 300 AUTOMOBILES
Serpentine Drive Belt, Replace -> Installation -> Removal
Vehicle: 2007 Chrysler 300 Touring LWB 3.5 V6 GAS
Removal
- Rotate belt tensioner counterclockwise until it contacts a stop.
- Remove belt and slowly rotate tensioner into the freearm position. Do not let tensioner arm snap back to freearm position.
Installation
- Route belt around all pulleys except idler pulley.
- Rotate tensioner arm until it contacts a s...
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2007 Chrysler 300 AUTOMOBILES
Component location diagrams for most 2007 Chrysler 300 cars and light trucks sold in the U.S. from 1990+.
 Body Components Diagram for 2007 Chrysler 300 C LWB 5.7 V8 GASComponents on diagram: |
 Front of Vehicle Diagram for 2007 Chrysler 300 Limited 3.5 V6 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2007 Chrysler 300 AUTOMOBILES
OEM drawn wiring diagrams for most 2007 Chrysler 300 cars and light trucks sold in the U.S.
 2007 Chrysler 300 Limited 3.5 V6 GAS Wiring DiagramComponents on diagram: |
 2007 Chrysler 300 Limited 3.5 V6 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2007 Chrysler 300 AUTOMOBILES
OEM TSB listings for most 2007 Chrysler 300 cars and light trucks sold in the U.S. from 1985+.
|
Document: Chrome Clad Wheel Adapters For Proper Balancing Vehicle: 2007 Chrysler 300 2.7 V6 GAS Auto Systems: |
|
Document: SQUEAK OR GROAN SOUND WHEN RAISING OR LOWERING DOOR GLASS Vehicle: 2007 Chrysler 300 2.7 V6 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2007 Chrysler 300 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2007 Chrysler 300 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2007 Chrysler 300 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2007 Chrysler 300 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2007 Chrysler 300 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2007 Chrysler 300 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2007 Chrysler 300 vehicle.
|
| Access the Complete guide! |
