Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2007 Dodge Sprinter 2500 car and truck
repair procedures including Dodge engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2007 Dodge Sprinter 2500 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2007 Dodge Sprinter 2500
- 2007 Dodge Sprinter 2500 3.0 V6 DIESEL, CC:2987, Fuel Injection, Engine VIN:, Desg:5
- 2007 Dodge Sprinter 2500 3.5 V6 GAS, CC:3498, Fuel Injection, Engine VIN:, Desg:6
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Dodge Sprinter 2500 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Dodge Sprinter 2500 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Dodge Sprinter 2500 3.0 V6 DIESEL
- Secure vehicle to prevent it from rolling.
- Make installing reference marks on propeller shaft.
- Remove retaining bracket bolts.
- Remove propeller shaft bolts from rear axle and transmission at flange.
- Remove propeller shaft intermediate bearing nuts from retaining bracket and bracket for brake cable. The brake cable bracket is only installed in vehicles with wheelbas...
CLICK HERE TO GET FULL ACCESS TO 2007 Dodge Sprinter 2500 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Dodge Sprinter 2500 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Dodge Sprinter 2500 cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> U-Joint with Injected Rings -> U-Joint with Snap Rings
Vehicle: 2007 Dodge Sprinter 2500 3.0 V6 DIESEL
This procedure describes a propeller shaft equipped with a cardan joint in the tube yoke. For propeller shafts equipped with a companion/slip yoke, repeat the steps to remove the remaining cardan joint.
U-Joint with Snap Rings
Disassemble
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke.
- Position yoke with grease fitting if equipped, pointing up.
- Position a socket with a inside diameter large enough to receive bearing cap, beneath yoke on a press.
- Place another socket with an outside diameter smaller than bearing cap on ...
CLICK HERE TO GET FULL ACCESS TO 2007 Dodge Sprinter 2500 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Dodge Sprinter 2500 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Dodge Sprinter 2500 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Dodge Sprinter 2500 3.5 V6 GAS
- Secure vehicle to prevent it from rolling.
- Make installing reference marks on propeller shaft.
- Remove retaining bracket bolts.
- Remove propeller shaft bolts from rear axle and transmission at flange.
- Remove propeller shaft intermediate bearing nuts from retaining bracket and bracket for brake cable. The brake cable bracket is only installed in vehicles with wheelbas...
CLICK HERE TO GET FULL ACCESS TO 2007 Dodge Sprinter 2500 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Dodge Sprinter 2500 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Dodge Sprinter 2500 cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> U-Joint with Injected Rings -> U-Joint with Snap Rings
Vehicle: 2007 Dodge Sprinter 2500 3.5 V6 GAS
This procedure describes a propeller shaft equipped with a cardan joint in the tube yoke. For propeller shafts equipped with a companion/slip yoke, repeat the steps to remove the remaining cardan joint.
U-Joint with Snap Rings
Disassemble
- Tap outside of bearing cap with a drift to loosen snap ring.
- Remove snap rings from both sides of yoke.
- Position yoke with grease fitting if equipped, pointing up.
- Position a socket with a inside diameter large enough to receive bearing cap, beneath yoke on a press.
- Place another socket with an outside diameter smaller than bearing cap on ...
CLICK HERE TO GET FULL ACCESS TO 2007 Dodge Sprinter 2500 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
