Auto Parts Search
2007 Ford Escape CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Ford REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2007 Ford Escape car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Ford Escape automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2007 Ford Escape AUTOMOBILES
Disc Brakes -> Brake Pad Service
Vehicle: 2007 Ford Escape XLT 3.0 V6 GAS
- Remove and discard a portion of brake fluid from master cylinder.
- Raise and support vehicle, then remove wheel and tire assembly.
- Unclip speed sensor wiring from brake ho...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Ford Escape AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2007 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS
Do not swap driveshaft assembles from different vehicles. The Escape Hybrid drive shaft is longer than the driveshaft in the Escape/Mariner and is not interchangeable.
- With vehicle in NEUTRAL, position it on a hoist.
- Remove ground strap bolt.
- Remove and discard 6 front driveshaft-to-transfer case bolts and washers. Do not reuse CV joint bolts and washers. Install new bolts and washers or damage to vehicle may occur.
- Index-mark front driveshaft to center bearing.
- Remove and discard 4 universal joint cap strap bolts and 2 cap straps and remove front driveshaft. Do not reuse bolts a...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2007 Ford Escape AUTOMOBILES
Description
Vehicle: 2007 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS
The TPMS (Tire Pressure Monitor System) has the ability to monitor the air pressure of all five tires. The tire-mounted pressure sensors transmit signals to the TPMS module by using the valve stem as an antenna. These transmissions are sent approximately every 30 seconds when the vehicle speed exceeds 20 mph. The ...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2007 Ford Escape AUTOMOBILES
Starter, Replace
Vehicle: 2007 Ford Escape XLT 3.0 V6 GAS
Always disconnect battery ground cable at the battery before disconnecting starter motor battery terminal lead. If a tool is shorted at the starter motor battery terminal, the tool can quickly heat enough to cause a skin burn. Failure to follow this instruction may result in serious personal injury.
- Disconnect battery ground cable.
- Loosen band clamp and remove air filter element, tray and inlet snorkel.
- Disconnect transmission shift cable and adjustment lock from transmission manual control lever.
- Disconnect transmission shift cable rotating slide snap and position aside transmissi...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2007 Ford Escape AUTOMOBILES
Cabin Air Filter Service -> Ford Motor Co. -> 2005-07 Escape, Escape Hybrid, Mariner & Mariner Hybrid
Vehicle: 2007 Ford Escape XLT 2.3 L4 GAS
Under normal operating conditions the cabin air filter should be replaced every 15,000 miles. In dusty areas change the cabin air filter more often.
- Remove the two wiper pivot arms nuts, cowl panel grille pin-type retainers and cowl panel grille pin-type retainers, Fi...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2007 Ford Escape AUTOMOBILES
Ford Motor Co. Trucks -> Check Engine Lamp -> 2007-09 EEC-V -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool
Vehicle: 2007 Ford Escape XLT 3.0 V6 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-V system. If the lamp remains On or starts to blink, a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
The lamp illuminates when the ignition is first turned to the on position to check the ...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2007 Ford Escape AUTOMOBILES
Radiator, Replace
Vehicle: 2007 Ford Escape XLT 2.3 L4 GAS
- Drain engine cooling system into a suitable container.
- Recover A/C refrigerant.
- Match mark hood latch position prior to removal of bolts.
- Loosen hood latch nut, then remove hood latch bolts and position hood latch aside.
- Detach wiring harness pin-type retainers, then remove radiator support bracket bolt.
- Remove front impact severity sensor bolt.
- Disconnect electrical connector and remove front impact severity sensor.
- Remove pushpin r...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2007 Ford Escape AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2007 Ford Escape XLT 3.0 V6 GAS
- Raise and support vehicle.
- Remove righthand front wheel and tire assembly.
- Remove righthand ...
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2007 Ford Escape AUTOMOBILES
Component location diagrams for most 2007 Ford Escape cars and light trucks sold in the U.S. from 1990+.
 Engine Compartment Diagram for 2007 Ford Escape XLT 3.0 V6 GASComponents on diagram: |
 Door Components Diagram for 2007 Ford Escape XLT 2.3 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2007 Ford Escape AUTOMOBILES
OEM drawn wiring diagrams for most 2007 Ford Escape cars and light trucks sold in the U.S.
 2007 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS Wiring DiagramComponents on diagram: |
 2007 Ford Escape Limited 3.0 V6 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2007 Ford Escape AUTOMOBILES
OEM TSB listings for most 2007 Ford Escape cars and light trucks sold in the U.S. from 1985+.
|
Document: Red Triangle On and Stop Safely Now Message - DTC P1A0C Vehicle: 2007 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS Symptoms: |
|
Document: LOWER CONTROL ARM BUSHING INSPECTION PROCEDURE Vehicle: 2007 Ford Escape Hybrid 2.3 L4 ELECTRIC/GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2007 Ford Escape AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2007 Ford Escape cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2007 Ford Escape cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2007 Ford Escape cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2007 Ford Escape cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2007 Ford Escape SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2007 Ford Escape vehicle.
|
| Access the Complete guide! |
