Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2007 Hyundai Santa FE car and truck
repair procedures including Hyundai engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2007 Hyundai Santa FE automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2007 Hyundai Santa FE
- 2007 Hyundai Santa FE GLS 2.7 V6 GAS, CC:2656, Fuel Injection, Engine VIN:, Desg:D
- 2007 Hyundai Santa FE Limited 3.3 V6 GAS, CC:3342, Fuel Injection, Engine VIN:, Desg:E
- 2007 Hyundai Santa FE SE 3.3 V6 GAS, CC:3342, Fuel Injection, Engine VIN:, Desg:E
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Hyundai Santa FE AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Hyundai Santa FE cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Hyundai Santa FE GLS 2.7 V6 GAS
- Raise vehicle off ground and support it with safety stands in proper locations.
- Mark companion flange, flange yoke, and differential companion flange and rubber coupling with a line.
- Remove bolts securing driveline from companion flange. When removing driveline use care not to damage the boot. Insert a cloth into the boot to prevent it from being damaged.
- Separate driveline from transfer assembly.
- Remove center support bearing mounting bolts.
- M...
CLICK HERE TO GET FULL ACCESS TO 2007 Hyundai Santa FE DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Hyundai Santa FE AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Hyundai Santa FE cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2007 Hyundai Santa FE Limited 3.3 V6 GAS
- Loosen wheel nuts slightly.
- Raise and support vehicle and ensure it is secure supported.
- Remove front wheel nuts and front wheels. Do not damage hub bolts when removing front wheel and tire.
- Remove split pin and castle nut.
- Remove brake caliper mounting bolts and support caliper using mechanic wire.
- Remove tie rod end ball joint from steering knuckle.
- Remove tie rod castle nut.
- Disconnect ball joint from steering knuckle using suitable tool.
- Remove split pin and lower control arm mounting bolt from steering knuckle.
- Disconnect driveshaft from axle hub using plastic hammer.
- Push axl...
CLICK HERE TO GET FULL ACCESS TO 2007 Hyundai Santa FE DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Hyundai Santa FE AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Hyundai Santa FE cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2007 Hyundai Santa FE SE 3.3 V6 GAS
- Loosen wheel nuts slightly.
- Raise and support vehicle and ensure it is secure supported.
- Remove front wheel nuts and front wheels. Do not damage hub bolts when removing front wheel and tire.
- Remove split pin and castle nut.
- Remove brake caliper mounting bolts and support caliper using mechanic wire.
- Remove tie rod end ball joint from steering knuckle.
- Remove tie rod castle nut.
- Disconnect ball joint from steering knuckle using suitable tool.
- Remove split pin and lower control arm mounting bolt from steering knuckle.
- Disconnect driveshaft from axle hub using plastic hammer.
- Push axl...
CLICK HERE TO GET FULL ACCESS TO 2007 Hyundai Santa FE DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Hyundai Santa FE AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Hyundai Santa FE cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2007 Hyundai Santa FE GLS 2.7 V6 GAS
Front
- Remove aluminum wheel cover using suitable tool.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove split pin and castle nut.
- Drain transaxle oil.
- On models equipped with ABS, detach wheel speed sensor cable from bracket.
- On all models, detach brake hose cable from bracket.
- Remove two flange bolts and detach knuckle from strut.
- Separate driveshaft from axle hub by tapping lightly with plastic hammer.
- Drive off driveshaft from transaxle or transfer inner shaft using a hammer and brass bar. Always use car...
CLICK HERE TO GET FULL ACCESS TO 2007 Hyundai Santa FE DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2007 Hyundai Santa FE vehicle.
|
| Access the Complete guide! |
