Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2007 Suzuki XL-7 car and truck
repair procedures including Suzuki engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2007 Suzuki XL-7 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2007 Suzuki XL-7
- 2007 Suzuki XL-7 3.6 V6 GAS, CC:3564, Fuel Injection
- 2007 Suzuki XL-7 Luxury 3.6 V6 GAS, CC:3564, Fuel Injection
- 2007 Suzuki XL-7 Limited 3.6 V6 GAS, CC:3564, Fuel Injection
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Suzuki XL-7 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Suzuki XL-7 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Suzuki XL-7 3.6 V6 GAS
- Raise and support vehicle.
- For front propeller shaft removal, proceed as follows:
- Drain transfer oil into a suitable container.
- Remove stabilizer bar mounting bracket bolts and pull down stabilizer bar.
- Give match marks on joint flange and propeller shaft.
- On models equipped with center support, remove center support mounting bolts...
CLICK HERE TO GET FULL ACCESS TO 2007 Suzuki XL-7 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Suzuki XL-7 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Suzuki XL-7 cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2007 Suzuki XL-7 3.6 V6 GAS
Disassemble
- Using special tool 09900-06108 or equivalent, remove 2 circlips.
- Using special tool 09926-48010 or equivalent, push spider bearing race out 0.12 - 0.16 in. from shaft yoke race. Before pushing it out, apply penetrate lubricant between bearing race and yoke race.
- Tapping yoke with a hammer, completely remove bearing race.
- Take out bearing race on other side in same way as in Step 2 and 3.
- Push out bearing race on flange yoke side as described in Step 1 and 2, and then, holding bearing race in a vise, tap flange yoke and take out race. Remove bearing race on opp...
CLICK HERE TO GET FULL ACCESS TO 2007 Suzuki XL-7 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Suzuki XL-7 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Suzuki XL-7 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2007 Suzuki XL-7 Luxury 3.6 V6 GAS
- Raise and support vehicle.
- For front propeller shaft removal, proceed as follows:
- Drain transfer oil into a suitable container.
- Remove stabilizer bar mounting bracket bolts and pull down stabilizer bar.
- Give match marks on joint flange and propeller shaft.
- On models equipped with center support, remove center support mounting bolts...
CLICK HERE TO GET FULL ACCESS TO 2007 Suzuki XL-7 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Suzuki XL-7 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Suzuki XL-7 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Left -> Right
Vehicle: 2007 Suzuki XL-7 3.6 V6 GAS
Left
- Raise and support vehicle, then remove wheel.
- Remove engine undercover.
- Remove axle shaft drive flange.
- Remove circlip and front spindle thrust washer.
- Remove drive shaft flange bolts and nuts.
- Place a suitable container under differential to catch fluid drips.
- Remove drive shaft assembly from left drive shaft case. To prevent breakage of boots (wheel side and differential side), do not contact them with other parts when removing drive shaft assembly.
- Remove drive shaft oil seal. Do not damage drive shaft joint and boot.
- Reverse procedure to install, noting the following:
- Torq...
CLICK HERE TO GET FULL ACCESS TO 2007 Suzuki XL-7 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Suzuki XL-7 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Suzuki XL-7 cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2007 Suzuki XL-7 Luxury 3.6 V6 GAS
Disassemble
- Using special tool 09900-06108 or equivalent, remove 2 circlips.
- Using special tool 09926-48010 or equivalent, push spider bearing race out 0.12 - 0.16 in. from shaft yoke race. Before pushing it out, apply penetrate lubricant between bearing race and yoke race.
- Tapping yoke with a hammer, completely remove bearing race.
- Take out bearing race on other side in same way as in Step 2 and 3.
- Push out bearing race on flange yoke side as described in Step 1 and 2, and then, holding bearing race in a vise, tap flange yoke and take out race. Remove bearing race on opp...
CLICK HERE TO GET FULL ACCESS TO 2007 Suzuki XL-7 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2007 Suzuki XL-7 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2007 Suzuki XL-7 cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2007 Suzuki XL-7 Limited 3.6 V6 GAS
Disassemble
- Using special tool 09900-06108 or equivalent, remove 2 circlips.
- Using special tool 09926-48010 or equivalent, push spider bearing race out 0.12 - 0.16 in. from shaft yoke race. Before pushing it out, apply penetrate lubricant between bearing race and yoke race.
- Tapping yoke with a hammer, completely remove bearing race.
- Take out bearing race on other side in same way as in Step 2 and 3.
- Push out bearing race on flange yoke side as described in Step 1 and 2, and then, holding bearing race in a vise, tap flange yoke and take out race. Remove bearing race on opp...
CLICK HERE TO GET FULL ACCESS TO 2007 Suzuki XL-7 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2007 Suzuki XL-7 vehicle.
|
| Access the Complete guide! |
