Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Chevrolet Trailblazer car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 Chevrolet Trailblazer automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 Chevrolet Trailblazer
- 2008 Chevrolet Trailblazer 4.2 L6 GAS, CID:256, Fuel Injection, Aspiration:256, Engine VIN:, Desg:S
- 2008 Chevrolet Trailblazer 5.3 V8 GAS, CID:325, Fuel Injection, Aspiration:325, Engine VIN:, Desg:M
- 2008 Chevrolet Trailblazer LT 4.2 L6 GAS, CID:256, Fuel Injection, Aspiration:256, Engine VIN:, Desg:S
- 2008 Chevrolet Trailblazer LT 5.3 V8 GAS, CID:325, Fuel Injection, Aspiration:325, Engine VIN:, Desg:M
- 2008 Chevrolet Trailblazer SS 6.0 V8 GAS, CID:364, Fuel Injection, Aspiration:364, Engine VIN:, Desg:H
BRAKE SERVICE PROCEDURES FOR 2008 Chevrolet Trailblazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Chevrolet Trailblazer cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Caliper Service -> Assemble -> Disassemble -> Inspection -> Installation -> Removal
Vehicle: 2008 Chevrolet Trailblazer LT 5.3 V8 GAS
Removal
- Siphon 2/3 of the brake fluid from master cylinder.
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Compress caliper pistons until they bottom in bores using suitable clamp, Fig. .
- Disconnect brake hose at caliper by removing inlet fitting bolt.
- Remove mounting bolts and caliper.
Inspection
Should it become required to remove the caliper for installation of new components, clean components in denatured alcohol, wipe dry using lint-free cloths. Blow out drilled passages and holes using compressed air. Inspect dust boots for punctures or tears. If punctures or tears are...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Trailblazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Chevrolet Trailblazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Chevrolet Trailblazer cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Master Cylinder
Vehicle: 2008 Chevrolet Trailblazer 4.2 L6 GAS
Master Cylinder
- On models equipped with manual brake system,disconnect master cylinder pushrod from brake pedal.
- On all models, disconnect all wire con...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Trailblazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Chevrolet Trailblazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Chevrolet Trailblazer cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Brake Pad Service -> Installation -> Removal
Vehicle: 2008 Chevrolet Trailblazer LT 4.2 L6 GAS
Removal
- Remove caliper as outlined in .
- Remove inboard pad with retainer spring.
- Remove outboard pad and position caliper on front suspension so brake hose will not support weight of caliper.
- Remove two sleeves from inboard ears of caliper.
- Remove four rubber bushings from grooves in each of caliper ears.
Installation
- Lubricate new sleeves, rubber bushings, bushing grooves and mounting bolt ends with lubricant part No. 19010909, or equivalent.
- Install new bushings and sleeves in caliper e...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Trailblazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Chevrolet Trailblazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Chevrolet Trailblazer cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Brake System Bleed -> Manual Bleed -> Pressure Bleed
Vehicle: 2008 Chevrolet Trailblazer 4.2 L6 GAS
Manual Bleed
- If vehicle is equipped with power brakes, remove vacuum reserve by applying brakes several times with engine off.
- Fill master cylinder reservoirs with suitable brake fluid. Ensure to always keep master cylinder reservoirs at least half full during entire bleeding procedure.
- If master cylinder is suspected to have air in bore, it must be bled first. To bleed master cylinder, proceed as follows:
- Disconnect forward brake pipe connection at master cylinder.
- Allow brake fluid to fill master cylinder bore until it begins to flow from forward pipe connector port.
- Connect and ...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Trailblazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Chevrolet Trailblazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Chevrolet Trailblazer cars and light trucks from 1990+.
Disc Brakes -> Delco Dual Piston Sliding Caliper -> Caliper Service -> Assemble -> Disassemble -> Inspection -> Installation -> Removal
Vehicle: 2008 Chevrolet Trailblazer SS 6.0 V8 GAS
Removal
- Siphon 2/3 of the brake fluid from master cylinder.
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Compress caliper pistons until they bottom in bores using suitable clamp, Fig. .
- Disconnect brake hose at caliper by removing inlet fitting bolt.
- Remove mounting bolts and caliper.
Inspection
Should it become required to remove the caliper for installation of new components, clean components in denatured alcohol, wipe dry using lint-free cloths. Blow out drilled passages and holes using compressed air. Inspect dust boots for punctures or tears. If punctures or tears are...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Trailblazer BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Chevrolet Trailblazer AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Chevrolet Trailblazer cars and light trucks from 1990+.
Disc Brakes -> Delco Single Piston Sliding Caliper -> Rotor, Replace -> 2WD Models -> 4WD Models -> Front -> Rear
Vehicle: 2008 Chevrolet Trailblazer LT 5.3 V8 GAS
2WD Models
Front
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove caliper as outlined in .
- Remove grease cap from hub/rotor, Fig. .
- Remove cotter pin, nut and washer.
- Remove hub/rotor from spindle, being careful not to damage spindle threads or outer bearing.
- Reverse procedure to install, noting the following:
- Apply high-temperature wheel bearing grease to inner and outer wheel bearings.
- Torque nut to 12 ft. lbs., while turning wheel assembly forward by hand, back nut off one flat or until hole i...
CLICK HERE TO GET FULL ACCESS TO 2008 Chevrolet Trailblazer BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
