Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Dodge Sprinter 2500 car and truck
repair procedures including Dodge engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 Dodge Sprinter 2500 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 Dodge Sprinter 2500
- 2008 Dodge Sprinter 2500 3.0 V6 DIESEL, CC:2987, Fuel Injection, Engine VIN:, Desg:5
- 2008 Dodge Sprinter 2500 3.5 V6 GAS, CC:3498, Fuel Injection, Engine VIN:, Desg:6
BRAKE SERVICE PROCEDURES FOR 2008 Dodge Sprinter 2500 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Dodge Sprinter 2500 cars and light trucks from 1990+.
Anti-Lock Brakes -> Sprinter -> System Service -> Automatic Load-Dependant Brake Pressure Controller (ALB) -> Brake System Bleed -> Component Replacement -> Controller Anti-Lock Brake (CAB) Module -> Front Wheel Speed Sensor -> Hydraulic Control Unit (HCU) -> Rear Wheel Speed Sensor
Vehicle: 2008 Dodge Sprinter 2500 3.0 V6 DIESEL
Brake System Bleed
The anti-lock brake system must be bled any time air enters the hydraulic system. It is important to note that excessive air in the brake system may set a primary pressure diagnostic trouble code in the control module.
Pressure or manual bleeding procedures can be used when bleeding the ABS system after hoses or brake lines have been disconnected. Bleeding the ABS hydraulic system is also necessary after replacement of the hydraulic assembly or wheel brakes. During bleeding procedures, ensure the brake fluid level remains close to the Full mark on the reservoir.
T...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Sprinter 2500 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Dodge Sprinter 2500 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Dodge Sprinter 2500 cars and light trucks from 1990+.
Anti-Lock Brakes -> Sprinter -> Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Tests -> Diagnostic Trouble Code Interpretation
Vehicle: 2008 Dodge Sprinter 2500 3.5 V6 GAS
Accessing Diagnostic Trouble Codes
Connect a suitably programmed scan tool to Data Link Connector (DLC) and follow manufacturer's instructions.
Diagnostic Trouble Code Interpretation
Refer to "Diag... "
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Sprinter 2500 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Dodge Sprinter 2500 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Dodge Sprinter 2500 cars and light trucks from 1990+.
Disc Brakes -> Tightening Specifications
Vehicle: 2008 Dodge Sprinter 2500 3.5 V6 GAS
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Sprinter 2500 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Dodge Sprinter 2500 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Dodge Sprinter 2500 cars and light trucks from 1990+.
Anti-Lock Brakes -> Sprinter -> Description
Vehicle: 2008 Dodge Sprinter 2500 3.0 V6 DIESEL
When wheel slip is detected during a brake application, the ABS enters anti-lock mode. During anti-lock braking, hydraulic pressure in the individual wheel circuits is controlled to prevent any wheel from slipping. A separate hydraulic line and specific solenoid valves are provided for each wheel. The ABS can decrease, hold, or increase hydraulic pressure to each wheel brake. The ABS cannot, however, increase hydraulic pressure above the amount which is transmitted by the master cylinder during braking.
The Controller Anti-Lock Brake (CAB) is used to monitor wheel speeds and modulate...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Sprinter 2500 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Dodge Sprinter 2500 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Dodge Sprinter 2500 cars and light trucks from 1990+.
Power Brake Units -> Description
Vehicle: 2008 Dodge Sprinter 2500 3.5 V6 GAS
These self contained vacuum hydraulic power braking units are of the vacuum suspended type. They use engine intake manifold vacuum or a vacuum pump along with atmospheric pressure for their power, eliminating the need for a vacuum reservoir. A mechanically operated control valve, with integral vacuum power diaphragms, controls the degree of brake application or release depending on amount of foot pressure applied to...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Sprinter 2500 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2008 Dodge Sprinter 2500 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2008 Dodge Sprinter 2500 cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> Aspen, Dakota & Durango -> Assemble -> Caravan & Town & Country -> Commander -> Compass, Grand Cherokee, Liberty, Nitro, Patriot & Wrangler -> Disassemble -> Front -> Full Size Pickup -> Inspection -> Installation -> Pacifica -> PT Cruiser -> Rear -> Removal -> Sprinter
Vehicle: 2008 Dodge Sprinter 2500 3.0 V6 DIESEL
Caravan & Town & Country
Refer to for caliper replacement procedures.
Disassemble
- Remove caliper from adapter and rotor as outlined under . Do not disconnect brake hose from caliper. Support caliper at all times to prevent brake hose damage.
- Position caliper away from rotor to prevent brake fluid spillage on machined surface, then place a small block of wood between caliper fingers to prevent piston damage during removal.
- Gently depress brake pedal to force caliper piston out of bore, then secure brake pedal at any position below one inch of pedal travel to prevent master cylinder br...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Sprinter 2500 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
