Auto Parts Search
We have info for following modifications of 2008 Nissan Rogue
- 2008 Nissan Rogue SL 2.5 L4 GAS, CC:2500, Fuel Injection
- 2008 Nissan Rogue S 2.5 L4 GAS, CC:2500, Fuel Injection
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Nissan Rogue AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Nissan Rogue cars and light trucks sold in the U.S. from mid 1990's+.
Component Replacement -> Body Control Module -> Installation -> Removal -> Transmitter
Vehicle: 2008 Nissan Rogue S 2.5 L4 GAS
Transmitter
Removal
- Deflate tire, then remove retaining nut an allow transmitter to fall into tire.
- Gently bounce tire so transmitter falls to bottom of tire.
- Place tire on suitable tire changing machine and break both tire beads. Ensure transmitter remains at bottom of tire.
- Turn tire so valve hole is at bottom, then bounce tire so transmitter is near valve hole.
- Lift tire onto turntable and position valve hole 270° from mounting/dismounting head, Fig. .
- Lubricate tire, then remove first side of tire.
- Reach inside of tire and remove transmitter.
- Remove second side of tire.
Installa...
CLICK HERE TO GET FULL ACCESS TO 2008 Nissan Rogue TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Nissan Rogue AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Nissan Rogue cars and light trucks sold in the U.S. from mid 1990's+.
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Interpretation -> Less Scan Tool -> With Scan Tool
Vehicle: 2008 Nissan Rogue SL 2.5 L4 GAS
Less Scan Tool
Accessing Diagnostic Trouble Codes
To start the self-diagnostics, place the ignition switch in the On position, then ground terminal of the tire pressure warning check connector. The fault location is indicated by the blinking of the low tire pressure warning lamp, Fig. . If the low tire pressure warning lamp is blinking repeatedly at 5 Hz, there is no fault occurring in the system.
Diagnostic Trouble Code Interpretation
[[table data]]Clearing Diagnostic Trouble Codes
In order to make it easier to find the cause of hard to duplicate malfunctions, the malfunction information is s...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Nissan Rogue TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Nissan Rogue AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Nissan Rogue cars and light trucks sold in the U.S. from mid 1990's+.
Reset Procedures
Vehicle: 2008 Nissan Rogue SL 2.5 L4 GAS
The Low Tire Pressure Warning lamp will illuminate briefly as a bulb check when the ignition switch is placed in the On position. This system uses radio frequency pressure sensors which monitor pressure in all 4 tires. When operating the vehicle at a speed above 25 mp...
CLICK HERE TO GET FULL ACCESS TO 2008 Nissan Rogue TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Nissan Rogue AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Nissan Rogue cars and light trucks sold in the U.S. from mid 1990's+.
Description
Vehicle: 2008 Nissan Rogue SL 2.5 L4 GAS
The TPMS (Tire Pressure Monitor System) is controlled by the Body Control Module (BCM). The BCM receives its tire pressure signal from the remote keyless entry receiver. The remote keyless entry receiver receives i...
CLICK HERE TO GET FULL ACCESS TO 2008 Nissan Rogue TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Nissan Rogue AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Nissan Rogue cars and light trucks sold in the U.S. from mid 1990's+.
Component Locations
Vehicle: 2008 Nissan Rogue SL 2.5 L4 GAS
Refer to F...
CLICK HERE TO GET FULL ACCESS TO 2008 Nissan Rogue TIRE PRESSURE MONITORING SYSTEM PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Nissan Rogue AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported 2008 Nissan Rogue cars and light trucks sold in the U.S. from mid 1990's+.
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2008 Nissan Rogue S 2.5 L4 GAS
Refer to Fig. for system wi...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Nissan Rogue TIRE PRESSURE MONITORING SYSTEM PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Nissan Rogue vehicle. |
Access the Complete guide! |