Auto Parts Search
2009 Dodge Avenger CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Dodge REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 Dodge Avenger car and truck
repair procedures including Dodge engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Dodge Avenger automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2009 Dodge Avenger AUTOMOBILES
Hydraulic Brake Systems -> Description -> Master Cylinder
Vehicle: 2009 Dodge Avenger SXT 2.7 V6 GAS
Master Cylinder
The master cylinder is a center valve master cylinder used for all applications. The brake fluid reservoir mounted on top and brake fluid level switch is mounted on the side of the reservoir.
The reservoir is indexed to prevent installation in the wrong direction. The cap diaphragm is slit to allow atmospheric pressure to equalize on both sides of diaphragm.
The primary and secondary outlet tubes of the master cylinder are connected to a junction block on non-ABS equipped vehicles. The master cylinder primary ...
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Dodge Avenger AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2009 Dodge Avenger SXT 2.4 L4 GAS
- On models equipped with anti-lock brakes, disconnect front speed sensor.
- On all models, remove brake hose clip and cotter pin.
- Remove drive shaft nut, Fig. .
- Loosen but do not remove ball joint nut using steering linkage puller tool No. MB991113, or equivalent.
- Loosen but do not remove tie rod end using steering linkage puller tool No. MB991113...
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Dodge Avenger AUTOMOBILES
Component Replacement -> Front -> Installation -> Rear -> Removal -> Tire Pressure Sensor -> TPMS Transponder
Vehicle: 2009 Dodge Avenger SXT 2.4 L4 GAS
Tire Pressure Sensor
The cap used on this valve stem contains an O-ring seal to prevent contamination and moisture from entering the valve stem. Retain this valve stem cap for reuse. Do not substitute a regular valve stem cap in its place.
The valve stem used on this vehicle is made of aluminum and the core is nickel plated brass. The original valve stem core must be reinstalled and not substituted with a valve stem core made of a different material. This is required to prevent corrosion in the valve stem caused by the different metals.
Removal
- Loosen the wheel lug nuts.
- Raise...
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2009 Dodge Avenger AUTOMOBILES
Starter, Replace
Vehicle: 2009 Dodge Avenger SXT 2.4 L4 GAS
- Disconnect and isolate battery ground cable at battery.
- Remove air cleaner box and air tube.
- Remove starter mounting bolt.
- Disconnect electrical connector at throttle body.
- Remove throttle body bolts and remove throttle body.
- Push starter under intake manifold.
- Tip starter nose to...
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2009 Dodge Avenger AUTOMOBILES
Cabin Air Filter Service -> Chrysler LLC -> 2007-09 Avenger & Sebring
Vehicle: 2009 Dodge Avenger SXT 2.7 V6 GAS
The cabin air filter should be replaced every 12,000 miles.
- Open the glove compartment.
- Push inward on the sides of the glove compartment bin, then lower the glove compartment.
- Remove the clip securing the dampener from the bin clip hole by sliding the retaining clip rearward.
- Pivot the glove compartment downward and detach the hooks from the instrument panel.
- Remove the glove compartment.
- Release the two tabs retaining the cabin air filter cover to the A/C-heater housing, then remove the cover, Fig. .
- Remove the cabin air filter element from the A/C-heater housing, Fig. .
- Ins...
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Dodge Avenger AUTOMOBILES
Chrysler LLC Cars -> Tire Pressure Monitoring System (TPMS) Warning Indicator -> 2008-09 Avenger -> Relearn -> Reset
Vehicle: 2009 Dodge Avenger SXT 2.7 V6 GAS
Reset
The Low Tire Pressure indicator lamp will flash slowly and sound a single tone when tire pressure is low. If tire pressure drops lower, the indicator lamp will flash rapidly and the tone will be continuous. When the tire is inflated to the proper pressure the lamp and tone will turn Off. The vehicle may need to be driven at a speed above 15 MPH for up to 10 minutes for the TPMS to receive this information. If the lamp remains On, a problem in the low tire warning system is present and the low tire warning system must be d...
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2009 Dodge Avenger AUTOMOBILES
Radiator, Replace
Vehicle: 2009 Dodge Avenger SE 2.7 V6 FLEX
- Disconnect negative cable from battery.
- Remove engine cover.
- Remove air box assembly.
- Recover A/C system.
- Drain coolant into a suitable container.
- Remove grille assembly.
- Remove under belly pan.
- Remove front bottom splash shield.
- Remove upper and lower radiator hoses at radiator.
- Disconnect radiator fan electrical connector.
- Separate radiator cooling fans from radiator.
- Disconnect A/C line at condenser/cooler.
- Remove transmission oil cooler tubes support bracket at left side of radiator. Plastic tanks, while stronger than brass are subject to damage by impact...
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2009 Dodge Avenger AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2009 Dodge Avenger SE 2.7 V6 FLEX
- Raise and support vehicle, then remove righthand front tire and wheel assembly.
- Remove splash shield.
- Loosen tensioner locking bolt and pivot bolt.
- Rotate tensioner clockwise and remove belt.
- Loosen...
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger SERPENTINE BELT SERVICE PROCEDURES
TECHNICAL SERVICE BULLETINS FOR 2009 Dodge Avenger AUTOMOBILES
OEM TSB listings for most 2009 Dodge Avenger cars and light trucks sold in the U.S. from 1985+.
|
Document: Pre Delivery - Front Brake Rotor Corrosion Inspection & Procedure Vehicle: 2009 Dodge Avenger R/T 3.5 V6 GAS Auto Systems: |
|
Document: Hard To Fill Or Fuel Nozzle Shuts Off Repeatedly Vehicle: 2009 Dodge Avenger R/T 3.5 V6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2009 Dodge Avenger AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2009 Dodge Avenger cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2009 Dodge Avenger cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2009 Dodge Avenger cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2009 Dodge Avenger cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2009 Dodge Avenger SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2009 Dodge Avenger vehicle.
|
| Access the Complete guide! |
