Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 Ford Explorer car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2009 Ford Explorer automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2009 Ford Explorer
- 2009 Ford Explorer XLT 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
- 2009 Ford Explorer XLT 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:8
- 2009 Ford Explorer Limited 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
- 2009 Ford Explorer Limited 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:8
- 2009 Ford Explorer Eddie Bauer 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
- 2009 Ford Explorer Eddie Bauer 4.6 V8 GAS, CID:281, Fuel Injection, Aspiration:281, Engine VIN:, Desg:8
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 2009 Ford Explorer XLT 4.6 V8 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Rear Load Leveling (CHECK SUSP) ->
Vehicle: 2009 Ford Explorer XLT 4.0 V6 GAS
The CHECK SUSP indicator lights when there is a fault of the rear load ...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Check Engine Lamp -> 2007-09 EEC-V -> Keep Alive Memory (KAM) Reset & PCM Reset Less Electronic Tester -> PCM Reset Using Generic Scan Tool
Vehicle: 2009 Ford Explorer XLT 4.6 V8 GAS
This lamp should light when the ignition is turned On. After engine starts, the lamp should go off, unless a fault condition is detected by the EEC-V system. If the lamp remains On or starts to blink, a diagnostic trouble code is stored in the PCM. Following diagnosis and repair, the Check Engine/MIL lamp will automatically reset when stored diagnostic trouble codes are cleared from PCM memory. The PCM reset procedure allows the scan tool to command the PCM to clear all diagnostic trouble codes.
The lamp illuminates when the ignition is first turned to the on position to check the ...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Electronic Throttle Control ->
Vehicle: 2009 Ford Explorer Eddie Bauer 4.6 V8 GAS
Electronic throttle displays when the system has malfunctioned and the engine has defaulted to a limp-home operation. On vehicles equipped with ...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Emission Maintenance Reminder Indicator ->
Vehicle: 2009 Ford Explorer Limited 4.0 V6 GAS
This lamp should light after approximately 60,000 miles of operation, Fig. . The amber lens lamp is located on the instrument panel and has the word Emissions, Emiss or EGR printed on it. After performing the required emission control maintenance, the module must be replaced or reset, depending on type of module used. On module equipped with reset feature, reset the module as follows:
- Turn ignition Off.
- On Aerostar models, the module is located under the instrument panel near the bulkhead connector.
- On Bronco, Explorer and F-Series, the module is attached to the instrument cluster to the left of ...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Ford Explorer AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported 2009 Ford Explorer cars and light trucks sold in the U.S. from 1990+.
Ford Motor Co. Trucks -> Tire Pressure Monitoring System (TPMS) Warning Indicator -> 2006-09 Explorer -> Relearn -> Reset -> TPMS Sensor Activation -> TPMS Sensor Training
Vehicle: 2009 Ford Explorer Eddie Bauer 4.6 V8 GAS
Reset
If the system detects low tire pressure, CHECK TIRE PRESSURE lamp will illuminate. Inflating tire(s) to recommended pressure will clear the tire message. Up to two minutes of driving above 20 mph may be required for the warning lamp to turn OFF after the tires have been filled to the recommended pressure.
Relearn
TPMS Sensor Activation
To conserve battery power, the TPMS sensors will go into a sleep mode after approximately 30 minutes of inactivity. The sensors will not transmit tire pressure information while in sleep mode. The sensors must be activated to transmit the lates...
CLICK HERE TO GET FULL ACCESS TO 2009 Ford Explorer MAINTENANCE LAMP RESET PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
