Auto Parts Search
2009 Mercury Mariner CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Mercury REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2009 Mercury Mariner car and truck
repair procedures including Mercury engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Mercury Mariner automobile. Try the Automotix DIY solution today!
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Mercury Mariner AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2009 Mercury Mariner 3.0 V6 GAS
Do not swap driveshaft assembles from different vehicles. The Escape Hybrid drive shaft is longer than the driveshaft in the Escape/Mariner and is not interchangeable.
- With vehicle in NEUTRAL, position it on a hoist.
- Remove ground strap bolt.
- Remove and discard 6 front driveshaft-to-transfer case bolts and washers. Do not reuse CV joint bolts and washers. Install new bolts and washers or damage to vehicle may occur.
- Index-mark front driveshaft to center bearing.
- Remove and discard 4 universal joint cap strap bolts and 2 cap straps and remove front driveshaft. Do not reuse bolts a...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Mariner DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2009 Mercury Mariner AUTOMOBILES
Component Replacement -> Installation -> Removal -> TPMS Sensor
Vehicle: 2009 Mercury Mariner Premier 3.0 V6 GAS
TPMS Sensor
The TPMS sensor battery may release hazardous chemicals if damaged. If these chemicals contact the skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If any part of the battery is swallowed, contact a physician immediately. When disposing of TPMS sensors, follow the correct procedures for hazardous material disposal. Failure to follow these instructions may result in serious personal injury.
Removal
Tire pressure sensors are manufactured in multiple colors based on their application. When installing a new senso...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Mariner TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2009 Mercury Mariner AUTOMOBILES
Starter, Replace
Vehicle: 2009 Mercury Mariner 3.0 V6 GAS
- With vehicle in Neutral, position it on a hoist.
- Disconnect battery ground cable.
- Remove terminal cover on starter solenoid.
- Remove B-terminal nut and disconnect wire.
- Remove S-terminal nut and disconnect wire.
- Remove two sta...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Mariner STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2009 Mercury Mariner AUTOMOBILES
Cabin Air Filter Service -> Ford Motor Co. -> 2008-09 Escape, Escape Hybrid, Mariner & Mariner Hybrid
Vehicle: 2009 Mercury Mariner 2.5 L4 GAS
Under normal operating conditions the cabin air filter should be replaced every 15,000 miles. In dusty areas change the cabin air filter more often.
- Remove the two wiper pivot arms nuts, then remove the wiper arms, Fig. .
- Remove the lefthand and righthand cowl end cap retainers, then the end caps, Fig. .
- ...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Mariner CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2009 Mercury Mariner AUTOMOBILES
Ford Motor Co. Trucks -> Electronic Throttle Control ->
Vehicle: 2009 Mercury Mariner 2.5 L4 GAS
Electronic throttle displays when the system has malfunctioned and the engine has defaulted to a limp-home operation. On vehicles equipped with ...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Mariner MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2009 Mercury Mariner AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2009 Mercury Mariner Hybrid 2.5 L4 ELECTRIC/GAS
Lower
- Drain coolant into a suitable container.
- Loosen hose clamp connecting hose to radiator.
- Loosen hose clamp connecting hose to thermostat housing.
- Remove hose from vehicle.
- Reverse procedure to ...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Mariner RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2009 Mercury Mariner AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2009 Mercury Mariner 3.0 V6 GAS
- With vehicle in neutral, raise and support vehicle.
- Remove pin-type retainer, five bolts and righthand splash shield.
- Using hex feature, rotate accessory drive belt tensioner counterclockwise ...
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Mariner SERPENTINE BELT SERVICE PROCEDURES
TECHNICAL SERVICE BULLETINS FOR 2009 Mercury Mariner AUTOMOBILES
OEM TSB listings for most 2009 Mercury Mariner cars and light trucks sold in the U.S. from 1985+.
|
Document: Hybrid Only - DTCS P0442, P0456 OR P1450 Vehicle: 2009 Mercury Mariner Hybrid 2.5 L4 ELECTRIC/GAS Auto Systems: |
|
Document: 6F35 TRANSMISSIONS BUILT BEFORE 10/6/2008 WITH NO CRANK AND/OR DTC P0706, P0707, P1702 Vehicle: 2009 Mercury Mariner Premier 3.0 V6 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Mariner TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2009 Mercury Mariner AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2009 Mercury Mariner cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2009 Mercury Mariner cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2009 Mercury Mariner cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2009 Mercury Mariner cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2009 Mercury Mariner SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
